- 您现在的位置：买卖IC网 > Datasheet目录985 > ISL76683EVAL1Z (Intersil)BOARD EVALUATION FOR ISL76683 Datasheet资料下载
参数资料
| 型号： | ISL76683EVAL1Z |
| 厂商： | Intersil |
| 文件页数： | 9/17页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ISL76683 |
| 标准包装： | 1 |
| 传感器类型： | 环境光 |
| 传感范围： | 1000lux ~ 64,000lux |
| 接口： | I²C |
| 灵敏度： | 540nm |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL76683 |
ISL76683
ADDRESS
TABLE 2. WRITE ONLY REGISTERS
REGISTER FUNCTIONS/
NAME DESCRIPTION
4. Photodiode Select Mode; Bits 3 and 2. This function controls
the mux attached to the two photodiodes. At Mode1, the mux
directs the current of Diode1 to the ADC. At Mode2, the mux
directs the current of Diode2 only to the ADC. Mode3 is a
b1xxx_xxxx
sync_iic
Writing a logic 1 to this address bit ends
the current ADC-integration and starts
another. Used only with External Timing
Mode.
sequential Mode1 and Mode2 with an internal subtract
function (Diode1 - Diode2).
TABLE 6. PHOTODIODE SELECT MODE; BITS 2 AND 3
bx1xx_xxxx
clar_int
Writing a logic 1 to this address bit clears
the interrupt.
BITS 3:2
0:0
MODE
MODE1. ADC integrates or converts Diode1 only. Current
is converted to an n-bit unsigned data.*
Command Register 00(hex)
The Read/Write command register has five functions:
1. Enable; Bit 7. This function either resets the ADC or enables
the ADC in normal operation. A logic 0 disables ADC to reset
mode. A logic 1 enables ADC to normal operation.
0:1
1:0
1:1
MODE2. ADC integrates or coverts Diode2 only. Current is
converted to an n-bit unsigned data.*
MODE3. A sequential MODE1 then MODE2 operation.
The difference current is an (n-1) signed data.*
No Operation.
TABLE 3. ENABLE
*n = 4, 8, 12,16 depending on the number of clock cycles
BIT 7
0
1
OPERATION
Disable ADC-Core to Reset-Mode (default)
Enable ADC-Core to Normal Operation
function.
5. Width; Bits 1 and 0. This function determines the number of
clock cycles per conversion. Changing the number of clock
cycles does more than just change the resolution of the
device; it also changes the integration time, which is the
2. ADCPD; Bit 6. This function puts the device in a power-down
mode. A logic 0 puts the device in normal operation. A logic 1
powers down the device.
period the device’s analog-to-digital (A/D) converter samples
the photodiode current signal for a lux measurement.
TABLE 7. WIDTH
TABLE 4. ADCPD
BITS 1:0
NUMBER OF CLOCK CYCLES
BIT 6
0
1
OPERATION
Normal Operation (default)
Power-Down
0:0
0:1
1:0
2 16 = 65,536
2 12 = 4,096
2 8 = 256
For proper shut down operation, it is recommended to disable
1:1
2 4 = 16
ADC first then disable the chip. Specifically, the user should first
send I 2 C command with Bit 7 = 0 and then send I 2 C command
with Bit 6 = 1.
3. Timing Mode; Bit 5. This function determines whether the
integration time is done internally or externally. In Internal
Timing Mode, integration time is determined by an internal dual
speed oscillator (f OSC ), and the n-bit (n = 4, 8, 12,16) counter
inside the ADC. In External Timing Mode, integration time is
Control Register 01(hex)
The Read/Write control register has three functions:
1. Interrupt flag; Bit 5. This is the status bit of the interrupt. The
bit is set to logic high when the interrupt thresholds have been
triggered, and logic low when not yet triggered.
TABLE 8. INTERRUPT FLAG
determined by the time between two consecutive external-sync
sync_iic pulse commands.
TABLE 5. TIMING MODE
BIT 5 OPERATION
0
Internal Timing Mode. Integration time is internally
timed determined by f OSC , REXT, and number of clock
cycles.
1
External Timing Mode. Integration time is externally
timed by the I 2 C host.
BIT 5
0
1
OPERATION
Interrupt is cleared or not triggered yet
Interrupt is triggered
9
FN7697.7
March 24, 2014
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97632IRTZ-EVALZ | EVAL BOARD FOR ISL97632IRTZ |
| ISL97671IRZ-EVALZ | BOARD EVALUATION FOR ISL97671 |
| ISL97684IRTZEVALZ | EVAL BOARD LED DRIVER |
| ISL97801BOOSTEVALZ | EVAL BOARD FOR ISL97801 |
| ISLA118P50IR72EV1Z | EVAL BOARD FOR ISLA118P50IR74 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL78010 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Automotive Grade TFT-LCD Power Supply |
| ISL78010_11 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Automotive Grade TFT-LCD Power Supply |
| ISL78010ANZ | 功能描述:直流/直流开关调节器 AUTO GRD TFT-LCD PWR SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL78010ANZ-T | 功能描述:直流/直流开关调节器 AUTO GRD TFT-LCD PWR SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL78010EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL78010 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。