参数资料
| 型号： | ISL78213ARZ |
| 厂商： | Intersil |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 3A 16VQFN |
| 标准包装： | 75 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5.5 V |
| 输入电压： | 2.8 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-QFN（4x4） |
ISL78213
Synchronization Control
V EAMP
V CSA
DUTY
CYCLE
I L
V OUT
FIGURE 36. PWM OPERATION WAVEFORMS
SKIP Mode
Pulling the SYNCH pin LO (<0.4V) forces the converter into PFM
mode. The ISL78213 enters a pulse-skipping mode at light load
to minimize the switching loss by reducing the switching
frequency. Figure 37 illustrates the skip-mode operation. A zero-
cross sensing circuit shown in Figure 2 monitors the N-MOSFET
current for zero crossing. When 8 consecutive cycles of the
inductor current crossing zero are detected, the regulator enters
the skip mode. During the eight detecting cycles, the current in
the inductor is allowed to become negative. The counter is reset
to zero when the current in any cycle does not cross zero.
Once the skip mode is entered, the pulse modulation starts being
controlled by the SKIP comparator shown in Figure 2. Each pulse
cycle is still synchronized by the PWM clock. The P-MOSFET is
turned on at the clock's rising edge and turned off when the
output is higher than 1.5% of the nominal regulation or when its
current reaches the peak Skip current limit value. Then the
inductor current is discharging to 0A and stays at zero. The
internal clock is disabled and the output voltage reduces
gradually due to the load current discharging the output
capacitor. When the output voltage drops to the nominal voltage,
the P-MOSFET will be turned on again at the rising edge of the
internal clock as it repeats the previous operations.
The regulator resumes normal PWM mode operation when the output
voltage drops 1.5% below the nominal voltage.
13
The frequency of operation can be synchronized up to 4MHz by an
external signal applied to the SYNCH pin. The falling edge on the
SYNCH triggers the rising edge of the LX pulse. Make sure that the
minimum ON time of the LX node is greater than 140ns.
Overcurrent Protection
The overcurrent protection is realized by monitoring the CSA output
with the OCP comparator, as shown in Figure 2. The current sensing
circuit has a gain of 250mV/A, from the P-MOSFET current to the
CSA output. When the CSA output reaches 1.4V, which is equivalent
to 4.8A for the switch current, the OCP comparator is tripped to turn
off the P-MOSFET immediately. The overcurrent function protects
the switching converter from a shorted output by monitoring the
current flowing through the upper MOSFET.
Upon detection of an overcurrent condition, the upper MOSFET will
be immediately turned off and will not be turned on again until the
next switching cycle. Upon detection of the initial overcurrent
condition, the overcurrent fault counter is set to 1. If, on the
subsequent cycle, another overcurrent condition is detected, the OC
fault counter will be incremented. If there are 17 sequential OC fault
detections, the regulator will be shutdown under an overcurrent fault
condition. An overcurrent fault condition will result in the regulator
attempting to restart in a hiccup mode within the delay of four soft-
start periods. At the end of the fourth soft-start wait period, the fault
counters are reset and soft-start is attempted again. If the
overcurrent condition goes away during the delay of four soft-start
periods, the output will resume back into regulation point after
hiccup mode expires.
Short-Circuit Protection
The short-circuit protection SCP comparator monitors the VFB pin
voltage for output short-circuit protection. When the VFB is lower
than 0.2V, the SCP comparator forces the PWM oscillator
frequency to drop to 1/3 of the normal operation value. This
comparator is effective during start-up or an output short-circuit
event.
FN7550.2
December 4, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| ISL78214ARZ | IC REG BUCK SYNC ADJ 4A 16QFN |
| ISL78215AUZ | IC REG CTRLR BST FLYBK ISO 8MSOP |
| ISL78220ANEZ-T | IC PWM CONTROLLER |
| ISL78225ANEZ-T | IC PWM CONTROLLER |
| ISL78228ARZ | IC REG BUCK SYNC ADJ DL 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL78213ARZ-T | 功能描述:IC REG BUCK SYNC ADJ 3A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL78213ARZ-TR5303 | 制造商:Intersil Corporation 功能描述:- Tape and Reel |
| ISL78214 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:4A Low Quiescent Current High Efficiency Synchronous Buck Regulator |
| ISL78214ARZ | 功能描述:IC REG BUCK SYNC ADJ 4A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL78214ARZ-T | 功能描述:IC REG BUCK SYNC ADJ 4A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
发布紧急采购，3分钟左右您将得到回复。