参数资料
| 型号： | ISL8014IRZ |
| 厂商： | Intersil |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 4A 16QFN |
| 产品培训模块： | ISL8013/4 Synchronous Buck Regulators |
| 标准包装： | 75 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 5.5 V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 4A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-QFN（4x4） |
ISL8014
Thermal Shut-Down
The ISL8014 has built-in thermal protection. When the
internal temperature reaches +140°C, the regulator is
completely shut down. As the temperature drops to
+115°C, the ISL8014 resumes operation by stepping
through the soft-start.
Applications Information
Output Inductor and Capacitor Selection
To consider steady state and transient operations,
ISL8014 typically uses a 1.5μH output inductor. The
higher or lower inductor value can be used to optimize
the total converter system performance. For example, for
higher output voltage 3.3V application, in order to
decrease the inductor current ripple and output voltage
ripple, the output inductor value can be increased. It is
recommended to set the ripple inductor current
approximately 30% of the maximum output current for
optimized performance. The inductor ripple current can
In Table 1, the minimum output capacitor value is given
for the different output voltage to make sure that the
whole converter system is stable. Additional output
capacitance should be added for better performances in
applications where high load transient or low output
ripple is required. It is recommended to check the
system level performance along with the simulation
model.
Output Voltage Selection
The output voltage of the regulator can be programmed
via an external resistor divider that is used to scale the
output voltage relative to the internal reference voltage
and feed it back to the inverting input of the error
amplifier. Refer to Figure 1.
The output voltage programming resistor, R 3 , will depend
on the value chosen for the feedback resistor and the
desired output voltage of the regulator. The value for the
feedback resistor is typically between 10k Ω and 100k Ω,
as shown in Equation 4.
V O ? ? 1 – --------- ?
L ? f S
R 2 ? 0.8V
R 3 = ----------------------------------
be expressed as shown in Equation 3:
? V O ?
? V IN ?
Δ I = -------------------------------------
(EQ. 3)
(EQ. 4)
V OUT – 0.8V
If the output voltage desired is 0.8V, then R 3 is left
unpopulated and R 2 is shorted. There is a leakage
current from VIN to LX. It is recommended to preload the
The inductor’s saturation current rating needs to be at
least larger than the peak current. The ISL8014 protects
the typical peak current 6A. The saturation current needs
be over 7A for maximum output current application.
ISL8014 uses internal compensation network and the
output capacitor value is dependent on the output
voltage. The ceramic capacitor is recommended to be
X5R or X7R. The recommended X5R or X7R minimum
output capacitor values are shown in Table 1.
TABLE 1. OUTPUT CAPACITOR VALUE vs V OUT
output with 10μA minimum. For better performance, add
47pF in parallel with R 2 (100k Ω).
Input Capacitor Selection
The main functions for the input capacitor are to provide
decoupling of the parasitic inductance and to provide
filtering function to prevent the switching current flowing
back to the battery rail. Two 22μF X5R or X7R ceramic
capacitors are a good starting point for the input
capacitor selection.
V OUT
(V)
0.8
1.2
1.5
1.8
2.5
3.3
3.6
C OUT
(μF)
2 x 22
2 x 22
2 x 22
2 x 22
2 x 22
2 x 22
2 x 22
L
(μH)
1.0~2.2
1.0~2.2
1.5~3.3
1.5~3.3
1.5~3.3
2.2~4.7
2.2~4.7
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications
at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by
Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any
infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any
patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
14
FN6576.4
November 23, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| ISL8016IRAJZ | IC REG BUCK SYNC ADJ 6A 20QFN |
| ISL8022IRZ-T7A | IC REG BUCK SYNC ADJ DL 12DFN |
| ISL8024IRTAJZ-T | IC VOLTAGE REGULATOR |
| ISL8033IRZ | IC REG BUCK SYNC ADJ 3A DL 24QFN |
| ISL8036IRZ | IC REG BUCK SYNC ADJ 3A 24QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8014IRZS2715 | 制造商:Intersil Corporation 功能描述:S SPEC FOR TRACKING BROADCOM BUSINESS ONLY-SOLD THRU DISTI - Rail/Tube |
| ISL8014IRZ-T | 功能描述:IC REG BUCK SYNC ADJ 4A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1 系列:EZBuck™ 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.8 V ~ 22.1 V 输入电压:3 V ~ 26 V PWM 型:电流模式 频率 - 开关:1.5MHz 电流 - 输出:1.8A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 包装:剪切带 (CT) 供应商设备封装:8-DFN（2x2） 其它名称:785-1276-1 |
| ISL8014IRZ-TS2715 | 制造商:Intersil Corporation 功能描述:S SPEC FOR TRACKING BROADCOM BUSINESS ONLY-SOLD THRU DISTI - Tape and Reel |
| ISL8016 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:6A Low Quiescent Current High Efficiency Synchronous Buck Regulator |
| ISL8016_1105 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:6A Low Quiescent Current High Efficiency Synchronous Buck Regulator |
发布紧急采购，3分钟左右您将得到回复。