- 您现在的位置：买卖IC网 > PDF目录13647 > ISL8023AIRTAJZ (Intersil)IC VOLTAGE REGULATOR PDF资料下载
参数资料
| 型号： | ISL8023AIRTAJZ |
| 厂商： | Intersil |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE REGULATOR |
| 标准包装： | 100 |
| 系列： | * |
ISL8023, ISL8024
V O ? ? 1 – --------- ? (EQ. 3)
L ? f S
R 2 = R 3 ? ------------ – 1 ?
V O
? VFB
?
Soft Start-Up
The soft start-up reduces the in-rush current during the start-up.
The soft-start block outputs a ramp reference to the input of the
error amplifier. This voltage ramp limits the inductor current as
well as the output voltage speed so that the output voltage rises
in a controlled fashion. When VFB is less than 0.1V at the
beginning of the soft-start, the switching frequency is reduced to
200kHz so that the output can start-up smoothly at light load
condition. During soft-start, the IC operates in the SKIP mode to
support pre-biased output condition.
Tie SS to SGND for internal soft-start approximately 1ms.
Connect a capacitor from SS to SGND to adjust the soft-start
time. This capacitor, along with an internal 1.6μA current source,
sets the soft-start interval of the converter, T SS as shown by
Equation 2.
C SS [ μ F ] = 3.33 ? T SS [ s ] (EQ. 2)
C ss must be less than 33nF to insure proper soft-start reset after
fault condition.
Enable
The enable (EN) input allows the user to control the turning on or
off the regulator for purposes such as power-up sequencing.
When the regulator is enabled, there is typically a 600μs delay
for waking up the bandgap reference and then the soft-start-up
begins.
Discharge Mode (Soft-Stop)
When a transition to shutdown mode occurs or the VIN UVLO is
set, the outputs discharge to GND through an internal 100 Ω
switch.
Power MOSFETs
The power MOSFETs are optimized for best efficiency. The
ON-resistance for the P-FET is typically 45m Ω and the
ON-resistance for the N-FET is typically 19m Ω .
100% Duty Cycle
The ISL8023, ISL8024 features 100% duty cycle operation to
maximize the battery life. When the battery voltage drops to a
level that the ISL8023, ISL8024 can no longer maintain the
regulation at the output, the regulator completely turns on the
P-FET. The maximum dropout voltage under the 100% duty-cycle
operation is the product of the load current and the
ON-resistance of the P-FET.
Thermal Shut-Down
The ISL8023, ISL8024 has built-in thermal protection. When the
internal temperature reaches +150°C, the regulator is completely
shutdown. As the temperature drops to +125°C, the ISL8023,
ISL8024 resumes operation by stepping through the soft-start.
Applications Information
Output Inductor and Capacitor Selection
To consider steady state and transient operations, ISL8023,
ISL8024 typically uses a 1.0μH output inductor. The higher or
lower inductor value can be used to optimize the total converter
system performance. For example, for higher output voltage 3.3V
application, in order to decrease the inductor current ripple and
output voltage ripple, the output inductor value can be increased.
It is recommended to set the ripple inductor current
approximately 30% of the maximum output current for optimized
performance. The inductor ripple current can be expressed as
shown in Equation 3:
? V O ?
? V IN ?
Δ I = ---------------------------------------
The inductor’s saturation current rating needs to be at least
larger than the peak current. The ISL8023, ISL8024 protects the
typical peak current 4.8A/6.5A. The saturation current needs be
over 7A for maximum output current application.
ISL8023, ISL8024 uses internal compensation network and the
output capacitor value is dependent on the output voltage. The
ceramic capacitor is recommended to be X5R or X7R. The
recommended X5R or X7R minimum output capacitor values are
shown in Table 1.
In Table 1, the minimum output capacitor value is given for the
different output voltage to make sure that the whole converter
system is stable. Additional output capacitance should be added
for better performances in applications where high load transient
or low output ripple is required. It is recommended to check the
system level performance along with the simulation model.
Output Voltage Selection
The output voltage of the regulator can be programmed via an
external resistor divider that is used to scale the output voltage
relative to the internal reference voltage and feed it back to the
inverting input of the error amplifier. Refer to Figure 2.
The output voltage programming resistor, R 2 , will depend on the
value chosen for the feedback resistor and the desired output
voltage of the regulator. The value for the feedback resistor is
typically between 10k Ω and 100k Ω, as shown in Equation 4.
(EQ. 4)
If the output voltage desired is 0.6V, then R 3 is left unpopulated
and R 2 is shorted. There is a leakage current from VIN to PHASE.
It is recommended to preload the output with 10μA minimum.
For better performance, add 15pF in parallel with R 2 (100k Ω).
Check loop analysis before use in application.
Input Capacitor Selection
The main functions for the input capacitor are to provide
decoupling of the parasitic inductance and to provide filtering
function to prevent the switching current flowing back to the
battery rail. At least two 22μF X5R or X7R ceramic capacitors are
a good starting point for the input capacitor selection.
16
FN7812.3
March 24, 2014
相关PDF资料 |
PDF描述 |
|---|---|
| 400BXC3.3MEFCT810X16 | CAP ALUM 3.3UF 400V 20% RADIAL |
| SC1212-222 | INDUCTOR SMD 2200UH 20A 1KHZ |
| RSM15DSUN | CONN EDGECARD 30POS DIP .156 SLD |
| RMM15DSUN | CONN EDGECARD 30POS DIP .156 SLD |
| RSM15DSUH | CONN EDGECARD 30POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8023AIRTAJZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL8023AIRTAJZ-T7A | 功能描述:IC REG BUCK SYNC ADJ 3A 16TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1 系列:EZBuck™ 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.8 V ~ 22.1 V 输入电压:3 V ~ 26 V PWM 型:电流模式 频率 - 开关:1.5MHz 电流 - 输出:1.8A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 包装:剪切带 (CT) 供应商设备封装:8-DFN（2x2） 其它名称:785-1276-1 |
| ISL8023EVAL3Z | 功能描述:电源管理IC开发工具 ISL8023 EVALUATION BOARD 3 - 16 LD TQFN - RoHS COMPLIANT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ISL8023IRTAJZ | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL8023IRTAJZ-T | 功能描述:IC VOLTAGE REGULATOR RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
发布紧急采购，3分钟左右您将得到回复。