- 您现在的位置：买卖IC网 > PDF目录15216 > ISL8105BIBZ-T (Intersil)IC REG CTRLR BUCK PWM VM 8-SOIC PDF资料下载
参数资料
| 型号： | ISL8105BIBZ-T |
| 厂商： | Intersil |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 8-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 100% |
| 电源电压： | 6.5 V ~ 14.4 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
ISL8105B
Overcurrent Protection (OCP)
V OUT OVER-CHARGED
V OUT PRE-BIASED
V OUT NORMAL
The overcurrent function protects the converter from a
shorted output by using the bottom-side MOSFET's
ON-resistance, r DS(ON) , to monitor the current. A resistor
(R BSOC ) programs the overcurrent trip level (see Typical
Application Diagram). This method enhances the converter's
efficiency and reduces cost by eliminating a current sensing
resistor. If overcurrent is detected, the output immediately
shuts off, it cycles the soft-start function in a hiccup mode
(2 dummy soft-start time-outs, then up to one real one) to
t0
t1
t2
provide fault protection. If the shorted condition is not
removed, this cycle will continue indefinitely.
Following POR (and 6.8ms delay), the ISL8105B initiates the
Overcurrent Protection sample and hold operation. The
FIGURE 3. SOFT-START WITH PRE-BIAS
soft-start ramp voltage exceeds the output; V OUT starts
seamlessly ramping from there. If the output is pre-biased to
a voltage above the expected value, as in the red curve,
neither MOSFET will turn on until the end of the soft-start, at
which time it will pull the output voltage down to the final
value. Any resistive load connected to the output will help
pull down the voltage (at the RC rate of the R of the load and
the C of the output capacitance).
If the V IN for the synchronous buck converter is from a
different supply that comes up after V BIAS , the soft-start
would go through its cycle, but with no output voltage ramp.
When V IN turns on, the output would follow the ramp of the
V IN from zero up to the final expected voltage (at close to
100% duty cycle, with COMP/EN pin >4V). If V IN is too fast,
there may be excessive inrush current charging the output
capacitors (only the beginning of the ramp, from zero to
V OUT matters here). If this is not acceptable, then consider
changing the sequencing of the power supplies, or sharing
the same supply, or adding sequencing logic to the
COMP/EN pin to delay the soft-start until the V IN supply is
ready (see “Input Voltage Considerations” on page 9).
If the IC is disabled after soft-start (by pulling COMP/EN pin
low), and then enabled (by releasing the COMP/EN pin),
then the full initialization (including OCP sample) will take
place. However, there is no new OCP sampling during
overcurrent retries. If the output is shorted to GND during
soft-start, the OCP will handle it, as described in the next
section.
7
BGATE driver is disabled to allow an internal 21.5μA current
source to develop a voltage across R BSOC . The ISL8105B
samples this voltage (which is referenced to the GND pin) at
the BGATE/BSOC pin, and holds it in a counter and DAC
combination. This sampled voltage is held internally as the
Overcurrent Set Point, for as long as power is applied, or
until a new sample is taken after coming out of a shut-down.
The actual monitoring of the bottom-side MOSFET's
on-resistance starts 200ns (nominal) after the edge of the
internal PWM logic signal (that creates the rising external
BGATE signal). This is done to allow the gate transition
noise and ringing on the LX pin to settle out before
monitoring. The monitoring ends when the internal PWM
edge (and thus BGATE) goes low. The OCP can be detected
anywhere within the above window.
If the regulator is running at high TGATE duty cycles (around
87% for 300kHz operation), then the BGATE pulse width
may not be wide enough for the OCP to properly sample the
r DS(ON) . For those cases, if the BGATE is too narrow (or not
there at all) for 3 consecutive pulses, then the third pulse will
be stretched and/or inserted to the 425ns minimum width.
This allows for OCP monitoring every third pulse under this
condition. This can introduce a small pulse-width error on the
output voltage, which will be corrected on the next pulse;
and the output ripple voltage will have an unusual 3-clock
pattern, which may look like jitter. If the OCP is disabled (by
choosing a too-high value of R BSOC , or no resistor at all),
then the pulse stretching feature is also disabled. Figure 4
illustrates the BGATE pulse width stretching, as the width
gets smaller.
FN6447.2
April 15, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| RBM28DRXN | CONN EDGECARD 56POS DIP .156 SLD |
| ISL8105AIBZ-T | IC REG CTRLR BUCK PWM VM 8-SOIC |
| RBM28DRXH | CONN EDGECARD 56POS DIP .156 SLD |
| VE-24N-EW-F2 | CONVERTER MOD DC/DC 18.5V 100W |
| RBM24DRTF | CONN EDGECARD 48POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8105BIRZ | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8105BIRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8105CRZ | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8105CRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| ISL8105EVAL1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:+5V or +12V Single-Phase Synchronous Buck Converter PWM Controller with Integrated MOSFET Gate Drivers |
发布紧急采购，3分钟左右您将得到回复。