参数资料
| 型号： | ISL83384ECAZA |
| 厂商： | Intersil |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | IC 2DRVR/2RCVR RS232 3V 20-SSOP |
| 标准包装： | 660 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232 |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
6
FN6017.3
March 15, 2005
Capacitor Selection
The charge pumps require 0.1
F or greater capacitors for
operation with 3.3V
≤ V
CC ≤ 5.5V. Increasing the capacitor
values (by a factor of 2) reduces ripple on the transmitter
outputs and slightly reduces power consumption. C2, C3,
and C4 can be increased without increasing C1’s value,
however, do not increase C1 without also increasing C2, C3,
and C4 to maintain the proper ratios (C1 to the other
capacitors).
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Operation Down to 2.7V
ISL83384E transmitter outputs meet RS-562 levels (±3.7V),
at the full data rate, with VCC as low as 2.7V. RS-562 levels
typically ensure interoperability with RS-232 devices.
Power Supply Decoupling
In most circumstances a 0.1
F bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple VCC to ground with a
capacitor of the same value as the charge-pump capacitor C1.
Connect the bypass capacitor as close as possible to the IC.
Transmitter Outputs when Exiting
Powerdown
Figure 5 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
transmitter is loaded with 3k
in parallel with 2500pF. Note
that the transmitters enable only when the magnitude of the
supplies exceed approximately 3V.
High Data Rates
The ISL83384E maintains the RS-232 ±5V minimum
transmitter output voltages even at high data rates. Figure 6
details a transmitter loopback test circuit, and Figure 7
illustrates the loopback test result at 120Kbps. For this test,
all transmitters were simultaneously driving RS-232 loads in
parallel with 1000pF, at 120Kbps. Figure 8 shows the
loopback results for a single transmitter driving 1000pF and
an RS-232 load at 250Kbps. The static transmitter was also
loaded with an RS-232 receiver.
TIME (20
s/DIV)
T1
T2
2V/DIV
5V/DIV
VCC = +3.3V
SHDN
FIGURE 5. TRANSMITTER OUTPUTS WHEN EXITING
POWERDOWN
C1 - C4 = 0.1
F
FIGURE 6. TRANSMITTER LOOPBACK TEST CIRCUIT
FIGURE 7. LOOPBACK TEST AT 120Kbps
ISL83384E
VCC
C1
C2
C4
C3
+
1000pF
V+
V-
5K
TIN
ROUT
C1+
C1-
C2+
C2-
RIN
TOUT
+
VCC
0.1
F
VCC
SHDN
T1IN
T1OUT
R1OUT
5
s/DIV
VCC = +3.3V
5V/DIV
C1 - C4 = 0.1
F
ISL83384E
相关PDF资料 |
PDF描述 |
|---|---|
| IDT723676L12PF8 | IC FIFO SYNC 16384X36 128QFP |
| MAX1305ECM+T | IC ADC 12BIT 4CH 2.8MSPS 48LQFP |
| ICL3225CAZ | IC 2DRVR/2RCVR RS232 3V 20-SSOP |
| MAX166CEWP+T | IC ADC 8BIT MPU COMP 20-SOIC |
| MS27656T21F1P | CONN RCPT 79POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL83384ECAZA-T | 功能描述:IC 2DRVR/2RCVR RS232 3V 20-SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL83384ECB | 制造商:Rochester Electronics LLC 功能描述:RS232 3V 2D/2R 15KV SHUTDOWN 18SOIC COM - Bulk |
| ISL83384ECB-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:【15kV ESD Protected, +3V to +5.5V, 1 Microamp, 250Kbps, RS-232 Transmitter/Receiver |
| ISL83384EIA | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:【15kV ESD Protected, +3V to +5.5V, 1 Microamp, 250Kbps, RS-232 Transmitter/Receiver |
| ISL83384EIA-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:【15kV ESD Protected, +3V to +5.5V, 1 Microamp, 250Kbps, RS-232 Transmitter/Receiver |
发布紧急采购，3分钟左右您将得到回复。