- 您现在的位置：买卖IC网 > PDF目录11408 > ISL84467IRTZ-T (Intersil)IC SWITCH QUAD SPDT 16TQFN PDF资料下载
参数资料
| 型号： | ISL84467IRTZ-T |
| 厂商： | Intersil |
| 文件页数： | 12/13页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPDT 16TQFN |
| 标准包装： | 1 |
| 功能： | 开关 |
| 电路： | 4 x SPDT |
| 导通状态电阻： | 400 毫欧 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 1.65 V ~ 4.5 V |
| 电流 - 电源： | 150nA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 标准包装 |
| 产品目录页面： | 1247 (CN2011-ZH PDF) |
| 其它名称： | ISL84467IRTZ-TDKR |
8
FN6521.1
July 23, 2008
.
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 9). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provide additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can be protected by adding a 1k
Ω resistor in series
with the logic input (see Figure 9). The resistor limits the input
current below the threshold that produces permanent damage,
and the sub-microamp input current produces an insignificant
voltage drop during normal operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low rON switch. Connecting Schottky
diodes to the signal pins (as shown in Figure 9) will shunt the
fault current to the supply or to ground, thereby protecting
the switch. These Schottky diodes must be sized to handle
the expected fault current.
.
Power-Supply Considerations
The ISL84467 construction is typical of most single supply
CMOS analog switches, in that they have two supply pins:
V+ and GND. V+ and GND drive the internal CMOS
switches and set their analog voltage limits. Unlike switches
with a 4.7V maximum supply voltage, the ISL84467 5.5V
maximum supply voltage provides plenty of room for the
10% tolerance of 4.3V supplies, as well as room for
overshoot and noise spikes.
The minimum recommended supply voltage is 1.65V. It is
important to note that the input signal range, switching times,
and ON-resistance degrade at lower supply voltages. Refer to
the “Electrical Specifications” tables starting on page 3 and the
“Typical Performance Curves” starting on page 9 for details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the input logic levels to switched
V+ and GND signals to drive the analog switch gate
terminals.
This family of switches cannot be operated with bipolar
supplies, because the input switching point becomes
negative in this configuration.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.5V and 1.4V)
over a supply range of 3.0V to 4.5V (see Figure 19). At 3.0V
the VIL level is about 0.53V. This is still above the 1.8V
CMOS guaranteed low output maximum level of 0.5V, but
noise margin is reduced.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation.
The ISL84467 has been designed to minimize the supply
current whenever the digital input voltage is not driven to the
supply rails (0V to V+). For example, driving the device with
2.85V logic (0V to 2.85V) while operating with a 4.2V supply
the device draws only 12A of current (see Figure 17 for
VIN = 2.85V).
FIGURE 8. V+ SERIES RESISTOR FOR ENHANCED ESD AND
LATCH-UP IMMUNITY
INx
COMx
100
Ω
NOx
NCx
V+
GND
C
OPTIONAL
PROTECTION
RESISTOR
FIGURE 9. OVERVOLTAGE PROTECTION
GND
VCOM
VNX
V+
INX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
ISL84467
相关PDF资料 |
PDF描述 |
|---|---|
| GRM2196R2A6R5DD01D | CAP CER 6.5PF 100V R2H 0805 |
| PIC16C558T-04I/SO | IC MCU OTP 2KX14 18SOIC |
| PIC18LF2423T-I/ML | IC PIC MCU FLASH 8KX16 28QFN |
| VE-261-CV-F1 | CONVERTER MOD DC/DC 12V 150W |
| MAX4510EUT+T | IC ANALOG SWITCH SPST SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL84467IVZ | 功能描述:IC SWITCH QUAD SPDT 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL84467IVZ-T | 功能描述:IC SWITCH QUAD SPDT 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 其它有关文件:STG4159 View All Specifications 标准包装:5,000 系列:- 功能:开关 电路:1 x SPDT 导通状态电阻:300 毫欧 电压电源:双电源 电压 - 电源，单路/双路(±):±1.65 V ~ 4.8 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:7-WFBGA，FCBGA 供应商设备封装:7-覆晶 包装:带卷 (TR) |
| ISL84514 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low-Voltage, Single Supply, SPST, Analog Switches |
| ISL84514_04 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low-Voltage, Single Supply, SPST, Analog Switches |
| ISL84514CB-T | 制造商:Intersil Corporation 功能描述:ANLG SW SGL SPST 12V 8SOIC N - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。