- 您现在的位置：买卖IC网 > PDF目录11072 > ISL84522IB (Intersil)IC SWITCH QUAD SPST 16SOIC PDF资料下载
参数资料
| 型号： | ISL84522IB |
| 厂商： | Intersil |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPST 16SOIC |
| 标准包装： | 48 |
| 功能： | 开关 |
| 电路： | 4 x SPST - NO |
| 导通状态电阻： | 100 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 2 V ~ 12 V，±2 V ~ 6 V |
| 电流 - 电源： | 50nA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
7
Detailed Description
The ISL84521, ISL84522, ISL84523 quad analog switches
offer precise switching capability from a bipolar ±2V to ±6V or
a single 2V to 12V supply with low on-resistance (65
) and
high speed switching (tON = 45ns, tOFF = 15ns). The devices
are especially well suited to portable battery powered
equipment thanks to the low operating supply voltage (2V),
low power consumption (1
W) and low leakage currents (1nA
max). High frequency applications also benefit from the wide
bandwidth, and the very high OFF isolation and crosstalk
rejection.
Supply Sequencing And Overvoltage Protection
As with any CMOS device, proper power supply sequencing
is required to protect the device from excessive input
currents which might permanently damage the IC. All I/O
pins contain ESD protection diodes from the pin to V+ and to
V- (Figure 8). To prevent forward biasing these diodes, V+
and V- must be applied before any input signals, and input
signal voltages must remain between V+ and V-. If these
conditions cannot be guaranteed, then one of the following
two protection methods should be employed.
Logic inputs can easily be protected by adding a 1k
resistor in series with the input (Figure 8). The resistor limits
the input current below the threshold that produces
permanent damage, and the sub-microamp input current
produces an insignificant voltage drop during normal
operation.
Adding a series resistor to the switch input defeats the
purpose of using a low RON switch, so two small signal
diodes can be added in series with the supply pins to provide
overvoltage protection for all pins (Figure 8). These
additional diodes limit the analog signal from 1V below V+ to
1V above V-. The low leakage current performance is
unaffected by this approach, but the switch resistance may
increase, especially at low supply voltages.
Power-Supply Considerations
The ISL8452X construction is typical of most CMOS analog
switches, in that they have three supply pins: V+, V-, and
GND. V+ and V- drive the internal CMOS switches and set
their analog voltage limits, so there are no connections
between the analog signal path and GND. Unlike switches
with a 13V maximum supply voltage, the ISL8452X 15V
maximum supply voltage provides plenty of room for the
10% tolerance of 12V supplies (±6V or 12V single supply),
as well as room for overshoot and noise spikes.
This family of switches performs equally well when operated
with bipolar or single voltage supplies, and bipolar supplies
need not be symmetrical. The minimum recommended
supply voltage is 2V or ±2V. It is important to note that the
input signal range, switching times, and ON-resistance
degrade at lower supply voltages. Refer to the electrical
specification tables and Typical Performance Curves for
details.
FIGURE 6. CROSSTALK TEST CIRCUIT
FIGURE 7. CAPACITANCE TEST CIRCUIT
Test Circuits and Waveforms (Continued)
0V or 2.4V
ANALYZER
V+
C
NO1 OR NC1
SIGNAL
GENERATOR
RL
GND
IN2
COM1
IN2
50
0V OR 2.4V
NO
COM2
NO2 OR NC2
C
V-
CONNECTION
V+
GND
NO OR NC
COM
IN
IMPEDANCE
ANALYZER
0V OR 2.4V
V-
FIGURE 8. OVERVOLTAGE PROTECTION
V-
VCOM
VNO OR NC
OPTIONAL PROTECTION
V+
INX
DIODE
OPTIONAL PROTECTION
DIODE
OPTIONAL
PROTECTION
RESISTOR
ISL84521, ISL84522, ISL84523
相关PDF资料 |
PDF描述 |
|---|---|
| VE-24M-IY-F3 | CONVERTER MOD DC/DC 10V 50W |
| VE-24M-IY-F2 | CONVERTER MOD DC/DC 10V 50W |
| ISL84521IV-T | IC SWITCH QUAD SPST 16TSSOP |
| ISL84521IV | IC SWITCH QUAD SPST 16TSSOP |
| VE-24M-IY-F1 | CONVERTER MOD DC/DC 10V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL84522IB-T | 功能描述:IC SWITCH QUAD SPST 16SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:- 电路:2 x SPST 导通状态电阻:20 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):3 V ~ 5.5 V 电流 - 电源:4.1mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:带卷 (TR) |
| ISL84522IBZ | 功能描述:IC SWITCH QUAD SPST 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL84522IBZ-T | 功能描述:IC SWITCH QUAD SPST 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL84522IR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Switch |
| ISL84522IR-T | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Switch |
发布紧急采购，3分钟左右您将得到回复。