- 您现在的位置：买卖IC网 > PDF目录11341 > ISL84762IUZ (Intersil)IC SWITCH DUAL SPDT 10MSOP PDF资料下载
参数资料
| 型号： | ISL84762IUZ |
| 厂商： | Intersil |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DUAL SPDT 10MSOP |
| 标准包装： | 98 |
| 功能： | 开关 |
| 电路： | 2 x SPDT |
| 导通状态电阻： | 600 毫欧 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 1.65 V ~ 3.6 V |
| 电流 - 电源： | 40nA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1247 (CN2011-ZH PDF) |
7
FN6105.1
September 15, 2008
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 9). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provided additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can be protected by adding a 1k
Ω resistor in
series with the logic input (see Figure 9). The resistor limits
the input current below the threshold that produces
permanent damage, and the sub-microamp input current
produces an insignificant voltage drop during normal
operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low rON switch. Connecting Schottky
diodes to the signal pins as shown in Figure 9 will shunt the
fault current to the supply or to ground thereby protecting the
switch. These Schottky diodes must be sized to handle the
expected fault current.
Power-Supply Considerations
The ISL84762 construction is typical of most single supply
CMOS analog switches, in that they have two supply pins:
V+ and GND. V+ and GND drive the internal CMOS
switches and set their analog voltage limits. Unlike switches
with a 4V maximum supply voltage, the ISL84762 4.8V
maximum supply voltage provides plenty of room for the
10% tolerance of 3.6V supplies, as well as room for
overshoot and noise spikes.
The minimum recommended supply voltage is 1.65V but the
part will operate with a supply below 1.5V. It is important to
note that the input signal range, switching times, and
ON-resistance degrade at lower supply voltages. Refer to
the “Electrical Specifications” tables beginning on page 3
and “Typical Performance Curves” beginning on page 8 for
details.
V+ and GND also power the internal logic and level shiftiers.
The level shiftiers convert the input logic levels to switched
V+ and GND signals to drive the analog switch gate
terminals.
This family of switches cannot be operated with bipolar
supplies, because the input switching point becomes
negative in this configuration.
FIGURE 8. V+ SERIES RESISTOR FOR ENHANCED ESD AND
LATCH-UP IMMUNITY
IN
COM
100
Ω
NO
NC
V+
GND
C
OPTIONAL
PROTECTION
RESISTOR
FIGURE 9. OVERVOLTAGE PROTECTION
GND
VCOM
VNX
V+
INX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
ISL84762
相关PDF资料 |
PDF描述 |
|---|---|
| PI5L200QE | IC ETHERNET SWITCH QUAD 16QSOP |
| PI2PCIE2212ZHE | IC MUX/DEMUX 2X1 28TQFN |
| DG442DYZ | IC SWITCH QUAD SPST 16SOIC |
| PI2PCIE412-DZHE | IC MUX/DEMUX QUAD 2X1 42TQFN |
| ISL84581IAZ | IC MULTIPLEXER 8X1 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL84762IUZ-T | 功能描述:IC SWITCH DUAL SPDT 10MSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL84780 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low Voltage, Single Supply, Quad 2:1 Analog Multiplexer |
| ISL84780IR | 功能描述:IC SWITCH QUAD SPDT 16TQFN RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:- 电路:2 x SPST 导通状态电阻:20 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):3 V ~ 5.5 V 电流 - 电源:4.1mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:带卷 (TR) |
| ISL84780IR-T | 功能描述:IC SWITCH QUAD SPDT 16TQFN RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:- 电路:2 x SPST 导通状态电阻:20 欧姆 电压电源:单电源 电压 - 电源，单路/双路(±):3 V ~ 5.5 V 电流 - 电源:4.1mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:带卷 (TR) |
| ISL84780IRZ | 功能描述:IC SWITCH QUAD SPDT 16TQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。