参数资料
| 型号： | ISL8483EIBZ-T |
| 厂商： | Intersil |
| 文件页数： | 13/14页 |
| 文件大小： | 0K |
| 描述： | TRANSCEIVER RS-485/422 ESD 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS422，RS485 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
8
FN6048.9
September 9, 2008
Application Information
RS-485 and RS-422 are differential (balanced) data
transmission standards for use in long haul or noisy
environments. RS-422 is a subset of RS-485, so RS-485
transceivers are also RS-422 compliant. RS-422 is a
point-to-multipoint (multidrop) standard, which allows only
one driver and up to 10 (assuming one unit load devices)
receivers on each bus. RS-485 is a true multipoint standard,
which allows up to 32 one unit load devices (any
combination of drivers and receivers) on each bus. To allow
for multipoint operation, the RS-485 specification requires
that drivers must handle bus contention without sustaining
any damage.
Another important advantage of RS-485 is the extended
common mode range (CMR), which specifies that the driver
outputs and receiver inputs withstand signals that range from
+12V to -7V. RS-422 and RS-485 are intended for runs as
long as 4000 feet, so the wide CMR is necessary to handle
ground potential differences, as well as voltages induced in
the cable by external fields.
Receiver Features
These devices utilize a differential input receiver for maximum
noise immunity and common mode rejection. Input sensitivity
is
±200mV, as required by the RS422 and RS-485
specifications.
Receiver input impedance surpasses the RS-422 spec of
4k
Ω, and meets the RS-485 “Unit Load” requirement of 12kΩ
minimum.
Receiver inputs function with common mode voltages as
great as
±7V outside the power supplies (i.e., +12V and
-7V), making them ideal for long networks where induced
voltages are a realistic concern.
All the receivers include a “fail-safe if open” function that
guarantees a high level receiver output if the receiver inputs
are unconnected (floating).
Receivers easily meet the data rates supported by the
corresponding driver.
ISL8483E, ISL8485E receiver outputs are three-stat-able via
the active low RE input.
Driver Features
The RS485, RS-422 driver is a differential output device that
delivers at least 1.5V across a 54
Ω load (RS-485), and at
least 2V across a 100
Ω load (RS-422). The drivers feature
low propagation delay skew to maximize bit width, and to
minimize EMI.
Drivers of the ISL8483E, ISL8485E are tri-stateable via the
active high DE input.
The ISL8483E driver outputs are slew rate limited to
minimize EMI, and to minimize reflections in un-terminated
or improperly terminated networks. Data rate on these slew
rate limited versions is a maximum of 250kbps. Outputs of
the ISL8485E driver are not limited, so faster output
transition times allow data rates of at least 10Mbps.
FIGURE 5A. TEST CIRCUIT
FIGURE 5B. MEASUREMENT POINTS
FIGURE 5. RECEIVER ENABLE AND DISABLE TIMES
Test Circuits and Waveforms (Continued)
1k
Ω
VCC
GND
SW
(SHDN) FOR ISL8483E ONLY
PARAMETER
DE
A
SW
tHZ
0
+1.5V
GND
tLZ
0
-1.5V
VCC
0
+1.5V
GND
0
-1.5V
VCC
0
+1.5V
GND
0
-1.5V
VCC
SIGNAL
GENERATOR
R
RO
RE
A
B
15pF
RO
3V
0V
1.5V
VOH
0V
1.5V
VOH - 0.5V
tHZ
RO
VCC
VOL
1.5V
VOL + 0.5V
tLZ
RE
OUTPUT HIGH
OUTPUT LOW
tZL, tZL(SHDN)
tZH, tZH(SHDN)
NOTE 7
ISL8483E, ISL8485E
相关PDF资料 |
PDF描述 |
|---|---|
| MS27656E15A35PA | CONN RCPT 37POS WALL MNT W/PINS |
| ISL8483IPZ | IC TXRX RS-485/422 5V 8-PDIP |
| IDT72V271LA15PFGI | IC FIFO SS 16384X18 15NS 64QFP |
| IDT72V265LA15PFI | IC FIFO SS 16384X18 15NS 64-TQFP |
| ISL8487IPZ | IC TXRX RS485/422 5V ESD 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8483EIBZ-T7A | 制造商:Intersil Corporation 功能描述:PB-FREE 8LD SOIC,250PT&R,-40+85,5V RS-485 15KV HBM TRANSCEIV - Tape and Reel 制造商:Intersil Corporation 功能描述:IC LINEAR 制造商:INTERSIL 功能描述:ISL8483 Series 4.5 - 5.5 V 250 k/bps 15kV ESD RS-485/RS-422 Transceiver - SOIC-8 制造商:Intersil 功能描述:8LD SOIC,250pT&R,-4 0+85,5V RS-485 15KV |
| ISL8483EIP | 功能描述:RS-422/RS-485 接口 IC 5V TXRX ESD RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| ISL8483EIPZ | 功能描述:IC TXRX RS485/422 5V ESD 8-PDIP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL8483IB | 功能描述:TRANSCEIVER RS-485/422 5V 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| ISL8483IB-T | 功能描述:TRANSCEIVER RS-485/422 5V 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。