参数资料
| 型号： | ISL8485IPZ |
| 厂商： | Intersil |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485/422 5V ESD 8-DIP |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS422，RS485 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
7
FN6046.8
February 28, 2006
Receiver Disable from Output Low
tLZ
CL = 15pF, SW = VCC, Figure 5
Full
-
10
50
ns
Maximum Data Rate
fMAX
Note 11
Full
250
-
kbps
Time to Shutdown (ISL8483 only)
tSHDN
Note 7
Full
50
200
600
ns
Driver Enable from Shutdown to
Output High (ISL8483 only)
tZH(SHDN) CL = 100pF, SW = GND, Figure 3, Notes 7, 8
Full
-
2000
ns
Driver Enable from Shutdown to
Output Low (ISL8483 only)
tZL(SHDN) CL = 100pF, SW = VCC, Figure 3, Notes 7, 8
Full
-
2000
ns
Receiver Enable from Shutdown to
Output High (ISL8483 only)
tZH(SHDN) CL = 15pF, SW = GND, Figure 5, Notes 7, 9
Full
-
2500
ns
Receiver Enable from Shutdown to
Output Low (ISL8483 only)
tZL(SHDN) CL = 15pF, SW = VCC, Figure 5, Notes 7, 9
Full
-
2500
ns
NOTES:
2. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless
otherwise specified.
3. Supply current specification is valid for loaded drivers when DE = 0V.
4. Applies to peak current. See “Typical Performance Curves” for more information.
5. When testing the ISL8483, keep RE = 0 to prevent the device from entering SHDN.
6. When testing the ISL8483, the RE signal high time must be short enough (typically <200ns) to prevent the device from entering SHDN.
7. The ISL8483 is put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts are guaranteed not
to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “Low-Power
Shutdown Mode” section.
8. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
9. Set the RE signal high time >600ns to ensure that the device enters SHDN.
10. Devices meeting these limits are denoted as “single unit load (1 UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus.
11. Guaranteed by characterization, but not tested.
Test Circuits and Waveforms
FIGURE 1. DRIVER VOD AND VOC
Electrical Specifications
Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified.
Typicals are at VCC = 5V, TA = 25°C, Note 2 (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNITS
D
DE
DI
VCC
VOD
VOC
R
Z
Y
ISL8483, ISL8485, ISL8488, ISL8489, ISL8490, ISL8491
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1099CEAE+T | IC ADC 10BIT SERIAL 16-SSOP |
| IDT72V265LA10PF | IC FIFO SS 16384X18 10NS 64-TQFP |
| ISL8488IPZ | IC TXRX RS-485/422 5V 8-PDIP |
| ISL8489EIBZ-T | IC TXRX RS485/422 5V ESD 14SOIC |
| ISL8488EIBZA-T | IC TXRX RS485/422 5V ESD 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8487 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL8487_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL8487E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:【15kV ESD Protected, 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL8487E_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:【15kV ESD Protected, 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL8487EIB | 功能描述:RS-422/RS-485 接口 IC 5V TXRX ESD RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。