- 您现在的位置：买卖IC网 > PDF目录381960 > ISL8487IB (INTERSIL CORP) 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers PDF资料下载
参数资料
| 型号： | ISL8487IB |
| 厂商： | INTERSIL CORP |
| 元件分类： | 通用总线功能 |
| 英文描述： | 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| 中文描述： | LINE TRANSCEIVER, PDSO8 |
| 封装： | PLASTIC, MS-012AA, SOIC-8 |
| 文件页数： | 8/13页 |
| 文件大小： | 430K |
| 代理商： | ISL8487IB |
8
Application Information
RS-485 and RS-422 are differential (balanced) data
transmission standards for use in long haul or noisy
environments. RS-422 is a subset of RS-485, so RS-485
transceivers are also RS-422 compliant. RS-422 is a point-
to-multipoint (multidrop) standard, which allows only one
driver and up to 10 (assuming one unit load devices)
receivers on each bus. RS-485 is a true multipoint standard,
which allows up to 32 one unit load devices (any
combination of drivers and receivers) on each bus. To allow
for multipoint operation, the RS-485 spec requires that
drivers must handle bus contention without sustaining any
damage.
Another important advantage of RS-485 is the extended
common mode range (CMR), which specifies that the driver
outputs and receiver inputs withstand signals that range
from +12V to -7V. RS-422 and RS-485 are intended for runs
as long as 4000’, so the wide CMR is necessary to handle
ground potential differences, as well as voltages induced in
the cable by external fields.
Receiver Features
These devices utilize a differential input receiver for maximum
noise immunity and common mode rejection. Input sensitivity
is
±
200mV, as required by the RS-422 and RS-485
specifications.
Receiver input resistance of 96k
surpasses the RS-422
spec of 4k
, and is eight times the RS-485 “Unit Load (UL)”
requirement of 12k
minimum. Thus, these products are
known as “one-eighth UL” transceivers, and there can be up
to 256 of these devices on a network while still complying
with the RS-485 loading spec.
Receiver inputs function with common mode voltages as
great as
±
7V outside the power supplies (i.e., +12V and
-7V), making them ideal for long networks where induced
voltages are a realistic concern.
All the receivers include a “fail-safe if open” function that
guarantees a high level receiver output if the receiver inputs
are unconnected (floating).
Receivers easily meet the data rates supported by the
corresponding driver, and receiver outputs are three-statable
via the active low RE input.
Driver Features
The RS-485 and RS-422 driver is a differential output device
that delivers at least 1.5V across a 54
load (RS-485), and
at least 2V across a 100
load (RS-422). The drivers feature
low propagation delay skew to maximize bit width, and to
minimize EMI.
Driver outputs are three-statable via the active high DE
input.
The ISL8487 and ISL81483 driver outputs are slew rate
limited to minimize EMI, and to minimize reflections in
unterminated or improperly terminated networks. Data rate
on these slew rate limited versions is a maximum of
250kbps. ISL81487 drivers are not limited, so faster output
transition times allow data rates of at least 5Mbps.
Data Rate, Cables, and Terminations
RS-485 and RS-422 are intended for network lengths up to
4000’, but the maximum system data rate decreases as the
transmission length increases. Devices operating at 5Mbps
are limited to lengths less than a few hundred feet, while the
250kbps versions can operate at full data rates with lengths
in excess of 1000’.
FIGURE 5A. TEST CIRCUIT
FIGURE 5B. MEASUREMENT POINTS
FIGURE 5. RECEIVER ENABLE AND DISABLE TIMES
Test Circuits and Waveforms
(Continued)
1k
V
CC
GND
SW
(SHDN) for ISL8487 and ISL81483 only.
PARAMETER
DE
A
SW
t
HZ
t
LZ
0
+1.5V
GND
0
-1.5V
V
CC
GND
t
ZH
(Note 6)
t
ZL
(Note 6)
t
ZH(SHDN)
(Note 7)
t
ZL(SHDN)
(Note 7)
0
+1.5V
0
-1.5V
V
CC
GND
0
+1.5V
0
-1.5V
V
CC
SIGNAL
GENERATOR
R
RO
RE
A
B
15pF
RO
3V
0V
1.5V
1.5V
V
OH
0V
1.5V
V
OH
- 0.5V
t
HZ
RO
V
CC
V
OL
1.5V
V
OL
+ 0.5V
t
LZ
RE
OUTPUT HIGH
OUTPUT LOW
t
ZL
, t
ZL(SHDN)
NOTE 7
t
ZH
, t
ZH(SHDN)
NOTE 7
NOTE 7
ISL8487, ISL81483, ISL81487
相关PDF资料 |
PDF描述 |
|---|---|
| ISL81487IB | 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL81483IP | 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL81487IP | 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL81483IB | 1/8 Unit Load, 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL8488IP | 5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8487IB-T | 功能描述:IC TXRX RS485/422 5V ESD 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| ISL8487IBZ | 功能描述:IC TXRX RS485/422 5V ESD 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL8487IBZ-T | 功能描述:IC TXRX RS485/422 5V ESD 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL8487IP | 功能描述:IC TXRX RS485/422 5V ESD 8-DIP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| ISL8487IPZ | 功能描述:IC TXRX RS485/422 5V ESD 8-DIP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。