参数资料
| 型号： | ISL8487IBZ-T |
| 厂商： | Intersil |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485/422 5V ESD 8-SOIC |
| 标准包装： | 2,500 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS422，RS485 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
6
FN6050.7
July 31, 2006
Driver Enable from Shutdown to
Output High
Full
-
1000
2000
ns
Driver Enable from Shutdown to
Output Low
Full
-
1000
2000
ns
Receiver Enable from Shutdown to
Output High
Full
-
800
2500
ns
Receiver Enable from Shutdown to
Output Low
Full
-
800
2500
ns
NOTES:
2. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless
otherwise specified.
3. Supply current specification is valid for loaded drivers when DE = 0V.
4. Applies to peak current. See “Typical Performance Curves” for more information.
5. When testing the ISL8487 and ISL81483, keep RE = 0 to prevent the device from entering SHDN.
6. When testing the ISL8487 and ISL81483, the RE signal high time must be short enough (typically <200ns) to prevent the device from entering
SHDN.
7. The ISL8487 and ISL81483 are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts are
guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See
“Low-Power Shutdown Mode” section.
8. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
9. Set the RE signal high time >600ns to ensure that the device enters SHDN.
10. Devices meeting these limits are denoted as “1/8 unit load (1/8 UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus,
so there can be 256 1/8 UL devices on a bus.
11. Devices meeting these limits are denoted as “1/4 unit load (1/4 UL)” transceivers. The RS-485 standard allows up to 32 Unit Loads on the bus,
so there can be 128 1/4 UL devices on a bus.
Test Circuits and Waveforms
FIGURE 1. DRIVER VOD AND VOC
Electrical Specifications
Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA = 25°C,
(Note 2) (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNITS
D
DE
DI
VCC
VOD
VOC
R
Z
Y
ISL8487, ISL81483, ISL81487
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2WZ-MV-F1 | CONVERTER MOD DC/DC 2V 60W |
| IDT72265LA10PF | IC FIFO 8KX18 LP 10NS 64QFP |
| V72B36M250B3 | CONVERTER MOD DC/DC 36V 250W |
| MS27497E16A26SD | CONN RCPT 26POS WALL MNT W/SCKT |
| IDT72V271LA15TFI | IC FIFO SS 16384X18 15NS 64QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8487IP | 功能描述:IC TXRX RS485/422 5V ESD 8-DIP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| ISL8487IPZ | 功能描述:IC TXRX RS485/422 5V ESD 8-DIP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL8488 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:5V, Low Power, High Speed or Slew Rate Limited, RS-485/RS-422 Transceivers |
| ISL8488E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:+-15kV ESD Protected, 5V, Low Power, High Speed and Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers |
| ISL8488E_07 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:【15kV ESD Protected, 5V, Low Power, High Speed and Slew Rate Limited, Full Duplex, RS-485/RS-422 Transceivers |
发布紧急采购，3分钟左右您将得到回复。