- 您现在的位置：买卖IC网 > PDF目录136444 > ISL8705IBZ (INTERSIL CORP) DSP-ADDRESS SEQUENCER, PDSO14 PDF资料下载
参数资料
| 型号： | ISL8705IBZ |
| 厂商： | INTERSIL CORP |
| 元件分类： | 数字信号处理外设 |
| 英文描述： | DSP-ADDRESS SEQUENCER, PDSO14 |
| 封装： | PLASTIC, MS-012AB, SOIC-14 |
| 文件页数： | 11/12页 |
| 文件大小： | 351K |
| 代理商： | ISL8705IBZ |
8
FN9250.0
March 14, 2006
Applications Usage
Using the ISL870XEVAL1 Platform
The ISL870XEVAL1 platform is the primary evaluation board
for this family of sequencers. See Figure 16 for photograph
and schematic.The evaluation board is shipped with an
ISL8702 mounted in the left position and with the other
device variants loose packed. In the following discussion,
test points names are bold on initial occurrence for
identification.
The VIN test point is the chip bias and can be biased from
2.5V to 24V. The VHI test point is for the ENABLE and
FAULT pull-up voltage which are limited to a maximum of
24V independent of VIN. The UV/OV resistor divider is set so
that a nominal 12V on the VMONITOR test point is compliant
and with a rising OV set at 13.2V and a falling UV set at
10.7V. These three test points (VIN,VHI and VMONITOR)
are brought out separately for maximum flexibility in
evaluation.
VMONITOR ramping up and down through the UV and OV
levels will result in the FAULT output signaling the out of
bound conditions by being released to pull high to the VHI
voltage as shown in Figures 6 and 7.
Once the voltage monitoring FAULT is resolved and where
applicable, the SEQ_EN(#) is satisfied, sequencing of the
ENABLE_X(#) outputs begins. When sequence enabled the
ENABLE_A, ENABLE_B, ENABLE_C and lastly
ENABLE_D are asserted in that order and when SEQ_EN is
disabled the order is reversed. See Figures 8 and 9
demonstrating the sequenced enabling and disabling of the
ENABLE outputs. The timing between ENABLE outputs is
set by the resistor values on the TB, TC, TD pins as shown.
Figure 10 illustrates the timing from either SEQ_EN and/or
VMONITOR being valid to ENABLE_A being asserted with a
10nF TIME capacitor. Figure 11 shows that ENABLE_X
outputs are pulled low even before VIN = 1V. This is critical
to ensure that a false enable is not signaled. Figure 12
illustrates the SEQ_EN# input disabling and enabling the
ISL8705 ENABLE# outputs. Notice the reversal in order and
delay timing from ENABLE_X# to ENABLE_X#. Figure 13
shows the time from SEQ_EN transition with the voltage
ramping across the TIME capacitor to TIME Vth being met.
This results in the immediate pull down of the TIME pin and
simultaneous ENABLE_A enabling.
FIGURE 6. VMONITOR RISING TO FAULT
FIGURE 7. VMONITOR FALLING TO FAULT
FAULT OUTPUT
VMON RISING
VMON > UV
VMON > OV
LEVEL
VMON FALLING
VMON > OV
VMON > UV
LEVEL
FAULT OUTPUT
ISL8700, ISL8701, ISL8702, ISL8703, ISL8704, ISL8705
相关PDF资料 |
PDF描述 |
|---|---|
| ICS932S208DG | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| IDT79R3041-20JG | 32-BIT, 20 MHz, RISC PROCESSOR, PQCC84 |
| ICS950902DFLFT | 200.4 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS843207CY-350 | 375 MHz, OTHER CLOCK GENERATOR, PQFP48 |
| JT00RT-18-32PA(023) | 32 CONTACT(S), ALUMINUM ALLOY, MALE, MIL SERIES CONNECTOR, CRIMP, RECEPTACLE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL870XEVAL1 | 功能描述:EVAL BOARD 1 FOR ISL870X RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| ISL8723EVAL1 | 功能描述:EVAL BOARD 1 FOR ISL8723 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| ISL8723IRZ | 功能描述:IC POWER SUPPLY SEQUENCER 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL8723IRZR5369 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL8723IRZ-T | 功能描述:IC POWER SUPPLY SEQUENCER 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。