- 您现在的位置：买卖IC网 > PDF目录20121 > ISL9000AIRBCZ (Intersil)IC REG LDO 1.5V/1.8V .3A 10-DFN PDF资料下载
参数资料
| 型号： | ISL9000AIRBCZ |
| 厂商： | Intersil |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.5V/1.8V .3A 10-DFN |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.5V，1.8V |
| 输入电压： | 2.3 V ~ 6.5 V |
| 稳压器数量： | 2 |
| 电流 - 输出： | 300mA（最小） |
| 电流 - 限制（最小）： | 350mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 管件 |
ISL9000A
Functional Description
The ISL9000A contains two high performance LDO’s. High
performance is achieved through a circuit that delivers fast
transient response to varying load conditions. In a quiescent
condition, the ISL9000A adjusts its biasing to achieve the lowest
standby current consumption.
The device also integrates current limit protection, smart thermal
shutdown protection, staged turn-on and soft-start. Smart
thermal shutdown protects the device against overheating.
Staged turn-on and soft-start minimize start-up input current
surges without causing excessive device turn-on time.
Power Control
The ISL9000A has two separate enable pins (EN1 and EN2) to
individually control power to each of the LDO outputs. When both
EN1 and EN2 are LOW, the device is in shutdown mode. During
this condition, all on-chip circuits are OFF, and the device draws
minimum current, typically less than 0.1μA.
When one or both of the enable pins are asserted, the device first
polls the output of the UVLO detector to ensure that VIN voltage is
at least about 2.1V. Once verified, the device initiates a start-up
sequence. During the start-up sequence, trim settings are first
read and latched. Then, sequentially, the bandgap, reference
voltage and current generation circuitry power-up. Once the
references are stable, a fast-start circuit quickly charges the
external reference bypass capacitor (connected to the CBYP pin)
to the proper operating voltage. After the bypass capacitor has
been charged, the LDOs power-up in their specified sequence.
Soft-start circuitry integrated into each LDO limits the initial
ramp-up rate to about 30μs/V to minimize current surge.
If EN1 is brought HIGH, and EN2 goes HIGH before the VO1
output stabilizes, the ISL9000A delays the VO2 turn-on until the
VO1 output reaches its target level.
If EN2 is brought high, and EN1 goes HIGH before VO2 starts its
output ramp, then VO1 turns on first and, the ISL9000A delays
the VO2 turn-on until the VO1 output reaches its target level.
If EN2 is brought HIGH, and EN1 goes HIGH after VO2 starts its
output ramp, then the ISL9000A immediately starts to ramp up
the VO1 output.
If both EN1 and EN2 are brought HIGH at the same time, the VO1
output has priority, and is always powered up first.
During operation, whenever the VIN voltage drops below about
1.8V, the ISL9000A immediately disables both LDO outputs.
When VIN rises back above 2.1V, the device re-initiates its
start-up sequence and LDO operation will resume automatically.
Reference Generation
The reference generation circuitry includes a trimmed bandgap,
a trimmed voltage reference divider, a trimmed current reference
generator, and an RC noise filter. The filter includes the external
capacitor connected to the CBYP pin. A 0.01μF capacitor
connected CBYP implements a 100Hz lowpass filter, and is
recommended for most high performance applications. For the
lowest noise application, a 0.1μF or greater CBYP capacitor
should be used. This filters the reference noise below the 10Hz to
1kHz frequency band, which is crucial in many noise-sensitive
applications.
The bandgap generates a zero temperature coefficient (TC)
voltage for the reference divider. The reference divider provides
the regulation reference, POR detection thresholds, and other
voltage references required for current generation and over-
temperature detection.
The current generator provides the references required for
adaptive biasing as well as references for LDO output current
limit and thermal shutdown determination.
LDO Regulation and Programmable Output
Divider
The LDO Regulator is implemented with a high-gain operational
amplifier driving a PMOS pass transistor. The design of the
ISL9000A provides a regulator that has low quiescent current,
fast transient response, and overall stability across all operating
and load current conditions. LDO stability is guaranteed for a 1μF
to 10μF output capacitor that has a tolerance better than 20%
and ESR less than 200m Ω . The design is performance-optimized
for a 1 μ F capacitor. Unless limited by the application, use of an
output capacitor value above 4.7μF is not normally needed as
LDO performance improvement is minimal.
Each LDO uses an independently trimmed 1V reference. An
internal resistor divider drops the LDO output voltage down to 1V.
This is compared to the 1V reference for regulation. The resistor
division ratio is programmed in the factory to one of the following
output voltages: 1.5V, 1.8V, 1.85V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V,
2.9V, 3.0V, and 3.3V.
Power-On Reset Generation
Each LDO has a separate Power-on Reset signal generation
circuit which outputs to the respective POR pins. The POR signal
is generated as follows:
A POR comparator continuously monitors the output of each LDO.
The LDO enters a power-good state when the output voltage is
above 94% of the expected output voltage for a period exceeding
the LDO PGOOD entry delay time. In the power-good state, the
open-drain PORx output is in a high-impedance state. An internal
100k Ω pull-up resistor pulls the pin up to the respective LDO
output voltage. An external resistor can be added between the
PORx output and the LDO output for a faster rise time, however,
the PORx output should not connect through an external resistor to
a supply greater than the associated LDO voltage.
The power-good state is exited when the LDO output falls below
90% of the expected output voltage for a period longer than the
PGOOD exit delay time. While power-good is false, the ISL9000A
pulls the respective POR pin low.
For LDO-1, the PGOOD entry delay time is fixed at about 2ms
while the PGOOD exit delay is about 25μs. For LDO-2, the PGOOD
entry and exit delays are determined by the value of the external
capacitor connected to the CPOR pin. For a 0.01μF capacitor, the
entry and exit delays are 200ms and 25μs respectively. Larger or
smaller capacitor values will yield proportionately longer or
shorter delay times. The POR exit delay should never be allowed
to be less than 10μs to ensure sufficient immunity against
transient induced false POR triggering.
11
FN6391.2
March 26, 2014
相关PDF资料 |
PDF描述 |
|---|---|
| T95R187K6R3ESSL | CAP TANT 180UF 6.3V 10% 2824 |
| VI-JWH-CY-B1 | CONVERTER MOD DC/DC 52V 50W |
| GMM43DTAD-S189 | CONN EDGECARD 86POS R/A .156 SLD |
| ESC36DRAH-S734 | CONN EDGECARD 72POS .100 R/A PCB |
| T95R226M035ESSL | CAP TANT 22UF 35V 20% 2824 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9000AIRBCZ-T | 功能描述:IC REG LDO 1.5V/1.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.25 V ~ 10 V 输入电压:2.9 V ~ 12 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:700mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:Digi-Reel® 其它名称:NCV8535MNADJR2GOSDKR |
| ISL9000AIRBJZ | 功能描述:IC REG LDO 1.5V/2.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.25 V ~ 10 V 输入电压:2.9 V ~ 12 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:700mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:Digi-Reel® 其它名称:NCV8535MNADJR2GOSDKR |
| ISL9000AIRBJZ-T | 功能描述:IC REG LDO 1.5V/2.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.25 V ~ 10 V 输入电压:2.9 V ~ 12 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:700mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:Digi-Reel® 其它名称:NCV8535MNADJR2GOSDKR |
| ISL9000AIRBLZ | 功能描述:IC REG LDO 1.5V/2.9V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.25 V ~ 10 V 输入电压:2.9 V ~ 12 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:700mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:Digi-Reel® 其它名称:NCV8535MNADJR2GOSDKR |
| ISL9000AIRBLZ-T | 功能描述:IC REG LDO 1.5V/2.9V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.25 V ~ 10 V 输入电压:2.9 V ~ 12 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:700mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:Digi-Reel® 其它名称:NCV8535MNADJR2GOSDKR |
发布紧急采购，3分钟左右您将得到回复。