- 您现在的位置：买卖IC网 > PDF目录20053 > ISL9000IRCCZ (Intersil)IC REG LDO 1.8V .3A 10-DFN PDF资料下载
参数资料
| 型号： | ISL9000IRCCZ |
| 厂商： | Intersil |
| 文件页数： | 10/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .3A 10-DFN |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.3 V ~ 6.5 V |
| 稳压器数量： | 2 |
| 电流 - 输出： | 300mA（最小） |
| 电流 - 限制（最小）： | 350mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 管件 |
ISL9000
If EN1 is brought high, and EN2 goes high before the VO1
output stabilizes, the ISL9000 delays the VO2 turn-on until
the VO1 output reaches its target level.
If EN2 is brought high, and EN1 goes high before VO2 starts
its output ramp, then VO1 turns on first and, the ISL9000
delays the VO2 turn-on until the VO1 output reaches its
target level.
If EN2 is brought high, and EN1 goes high after VO2 starts
its output ramp, then the ISL9000 immediately starts to ramp
up the VO1 output.
If both EN1 and EN2 are brought high at the same time, the
VO1 output has priority, and is always powered up first.
During operation, whenever the VIN voltage drops below
about 1.8V, the ISL9000 immediately disables both LDO
outputs. When VIN rises back above 2.1V, the device
re-initiates its start-up sequence and LDO operation will
resume automatically.
Reference Generation
The reference generation circuitry includes a trimmed
bandgap, a trimmed voltage reference divider, a trimmed
current reference generator, and an RC noise filter. The filter
includes the external capacitor connected to the CBYP pin.
A 0.01μF capacitor connected CBYP implements a 100Hz
lowpass filter, and is recommended for most high
performance applications. For the lowest noise application, a
0.1μF or greater CBYP capacitor should be used. This filters
the reference noise below the 10Hz to 1kHz frequency band,
which is crucial in many noise-sensitive applications.
The bandgap generates a zero temperature coefficient (TC)
voltage for the reference divider. The reference divider
provides the regulation reference, POR detection thresholds,
and other voltage references required for current generation
and over-temperature detection.
The current generator provides the references required for
adaptive biasing as well as references for LDO output
current limit and thermal shutdown determination.
LDO Regulation and Programmable Output Divider
The LDO Regulator is implemented with a high-gain
operational amplifier driving a PMOS pass transistor. The
design of the ISL9000 provides a regulator that has low
quiescent current, fast transient response, and overall
stability across all operating and load current conditions.
LDO stability is guaranteed for a 1μF to 10μF output
capacitor that has a tolerance better than 20% and ESR less
than 200m Ω . The design is performance-optimized for a 1μF
capacitor. Unless limited by the application, use of an output
capacitor value above 4.7μF is not normally needed as LDO
performance improvement is minimal.
Each LDO uses an independently trimmed 1V reference. An
internal resistor divider drops the LDO output voltage down
to 1V. This is compared to the 1V reference for regulation.
10
The resistor division ratio is programmed in the factory to
one of the following output voltages: 1.5V, 1.8V, 1.85V, 2.5V,
2.6V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V, and 3.3V.
Power-On Reset Generation
Each LDO has a separate Power-on Reset signal generation
circuit which outputs to the respective POR pins. The POR
signal is generated as follows:
A POR comparator continuously monitors the output of each
LDO. The LDO enters a power-good state when the output
voltage is above 94% of the expected output voltage for a
period exceeding the LDO PGOOD entry delay time (see the
following). In the power-good state, the open-drain PORx
output is in a high-impedance state. An internal 100k Ω
pull-up resistor pulls the pin up to the respective LDO output
voltage. An external resistor can be added between the
PORx output and the LDO output for a faster rise time,
however, the PORx output should not connect through an
external resistor to a supply greater than the associated
LDO voltage.
The power-good state is exited when the LDO output falls
below 90% of the expected output voltage for a period longer
than the PGOOD exit delay time. While power-good is false,
the ISL9000 pulls the respective POR pin low.
For LDO-1, the PGOOD entry delay time is fixed at about
2ms while the PGOOD exit delay is about 25μs. For LDO-2,
the PGOOD entry and exit delays are determined by the
value of the external capacitor connected to the CPOR pin.
For a 0.01μF capacitor, the entry and exit delays are 200ms
and 25μs respectively. Larger or smaller capacitor values will
yield proportionately longer or shorter delay times. The POR
exit delay should never be allowed to be less than 10μs to
ensure sufficient immunity against transient induced false
POR triggering.
Overheat Detection
The bandgap provides a proportional-to-temperature current
that is indicative of the temperature of the silicon. This
current is compared with references to determine if the
device is in danger of damage due to overheating. When the
die temperature reaches about +145°C, one or both of the
LDOs momentarily shut down until the die cools sufficiently.
In the overheat condition, only the LDO sourcing more than
50mA will be shut off. This does not affect the operation of
the other LDO. If both LDOs source more than 50mA and an
overheat condition occurs, both LDO outputs are disabled.
Once the die temperature falls back below about +110°C,
the disabled LDO(s) are re-enabled and soft-start
automatically takes place.
The ISL9000 provides short-circuit protection by limiting the
output current to about 475mA. If short circuited, an output
current of 475mA will cause die heating. If the short circuit
lasts long enough, the overheat detection circuit will turn off
the output.
FN9217.4
March 11, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| T95R687K6R3ESAL | CAP TANT 680UF 6.3V 10% 2824 |
| GRM188R71H272KA01D | CAP CER 2700PF 50V 10% X7R 0603 |
| HHR-650DA08F9 | BATTERY PACK NIMH 10.8V 6500 MAH |
| GRM1555C1H150JZ01D | CAP CER 15PF 50V 5% NP0 0402 |
| T95R337M016ESAL | CAP TANT 330UF 16V 20% 2824 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9000IRCCZ-T | 功能描述:IC REG LDO 1.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9000IRCJZ | 功能描述:IC REG LDO 1.8V/2.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9000IRCJZ-T | 功能描述:IC REG LDO 1.8V/2.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9000IRFCZ | 功能描述:IC REG LDO 2.5V/1.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9000IRFCZ-T | 功能描述:IC REG LDO 2.5V/1.8V .3A 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
发布紧急采购，3分钟左右您将得到回复。