- 您现在的位置：买卖IC网 > PDF目录17004 > ISL9000PLEV2 (Intersil)EVAL BOARD 1.85V/2.9V ISL9000PL PDF资料下载
参数资料
| 型号： | ISL9000PLEV2 |
| 厂商： | Intersil |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD 1.85V/2.9V ISL9000PL |
| 标准包装： | 1 |
| 每 IC 通道数： | 2 - 双 |
| 输出电压： | 1.85V，2.9V |
| 电流 - 输出： | 300mA，200mA |
| 输入电压： | 2.3 ~ 6.5 V |
| 稳压器类型： | 正，固定式 |
| 工作温度： | -40°C ~ 85°C |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL9000 |
Application Note 1210
What is Inside
The Evaluation Kit contains:
? ISL9000__EV2 Evaluation board
? The ISL9000 Data Sheet
? The ISL9000EV2 Users Guide (this document)
What is Needed
The following instruments will be needed to perform testing
(not provided):
? DC 6.5V/1A Power supply
? Two Digital Voltmeters (4.5 digit or better).
? Oscilloscope
? 2 channel, 0 to 400mA electronic load
? Cables and wires
Quick Setup Guide
Step 1: Place shunts on J3 between “EN1” and HI”, on J4
between “EN1” and HI”, and on J10 (CPOR). This is
the factory default connection.
Step 2: Set the power supply to 3.8V with a 1.0A current limit
(then turn off).
Step 3: Connect the power supply between VIN and GND
using connector J2.
Step 4: Connect two voltmeter positive leads to the VO1
“kelvin” connector (J13-1, “V1K”) and the VO2
“kelvin” connector (J13-5, “V2K”). The meters can
also be connected to the VO power pins J2-2 and J2-
4 or the banana jacks, but at higher currents, these
won’t reflect the output voltage as accurately as the
kelvin connections.
Connect the negative leads to GND J13-3. (To get
the best representation of the IC output voltage under
all output loading conditions, add a ground terminal
to the GNDk pad and connect the meter ground leads
there).
Step 5: Connect a third voltmeter to the input. This can be
connected to the J2 terminal, but at higher inputs, the
VIk terminal will give the most accurate reading of the
voltage at the ISL9000 VIN pin.
Step 6: (Optional) Connect an electronic load to one or both
of the outputs. For the VO1 output, use the VO1
power connector J2-2 (“V1P”). For the VO2 output,
use the VO2 power connector J2-4 (“V2P”).
Step 7: Monitor VO1and VO2. The voltages should reflect
the voltage of the selected part, i.e. the ISL9000NJ
EV2 board should have 3.3V and 2.8V outputs. For a
complete list of output voltages, see Table 1.
Step 8: Change the loading on each output and monitor the
output voltages
GND
Meter 3
+
Evaluation board option ID
Scope Probe Jacks
(not populated)
Banana Jacks
(not populated)
Power
Supply
Input
Power
0-5V/1.0A
Meter 1
+
+
Meter 2
Ch1 load
GND
Ch2 load
Daughter Card Connector
(not populated)
Logic Analyser connector
(not populated)
2
POR jumper: On for proper POR2 delay.
EN1 - Jumper on EN1 HI to enable LDO-1 output
EN2 - Jumper on EN2 HI to enable LDO-2 output
Add jumpers to add optional 100k ? EN pull down resistors.
FIGURE 1. BOARD CONNECTION DIAGRAM
相关PDF资料 |
PDF描述 |
|---|---|
| EEM31DTAD-S189 | CONN EDGECARD 62POS R/A .156 SLD |
| EBA24DTKS | CONN EDGECARD 48POS DIP .125 SLD |
| VE-27L-EY | CONVERTER MOD DC/DC 28V 50W |
| 0210490997 | CABLE JUMPER 1.25MM .152M 29POS |
| EBM24DCAH-S189 | CONN EDGECARD 48POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9001 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:LDO with Low ISUPPLY, High PSRR |
| ISL9001A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:LDO with Low ISUPPLY, High PSRR |
| ISL9001AIRBZ-T | 功能描述:IC REG LDO 1.5V .3A 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9001AIRCZ-T | 功能描述:低压差稳压器 - LDO W/ANNEAL SNGLDO LW I Q HI PSRR 1.8V8LDDFN RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| ISL9001AIRFZ-T | 功能描述:IC REG LDO 2.5V .3A 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
发布紧急采购，3分钟左右您将得到回复。