- 您现在的位置：买卖IC网 > PDF目录20148 > ISL9005IRNZ-T (Intersil)IC REG LDO 3.3V .3A 8-DFN PDF资料下载
参数资料
| 型号： | ISL9005IRNZ-T |
| 厂商： | Intersil |
| 文件页数： | 8/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .3A 8-DFN |
| 标准包装： | 6,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 6.5V |
| 电压 - 压降（标准）： | 0.2V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA（最小） |
| 电流 - 限制（最小）： | 350mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN（2x3） |
| 包装： | 带卷 (TR) |
ISL9005
Block Diagram
VIN
During operation, whenever the VIN voltage drops below
about 1.84V, the ISL9005 immediately disables the LDO
output. When VIN rises back above 2.1V, the device
re-initiates its start-up sequence and LDO operation will
resume automatically.
UVLO
CONTROL
LOGIC
SHORT CIRCUIT,
THERMAL PROTECTION,
SOFT-START
VO
Reference Generation
The reference generation circuitry includes a trimmed
bandgap, a trimmed voltage reference divider, a trimmed
current reference generator, and an RC noise filter.
The bandgap generates a zero temperature coefficient (TC)
voltage for the reference divider. The reference divider
provides the regulation reference and other voltage
EN
+
-
GND
references required for current generation and over-
temperature detection.
The current generator outputs references required for
adaptive biasing as well as references for LDO output
current limit and thermal shutdown determination.
LDO Regulation and Programmable Output Divider
The LDO Regulator is implemented with a high-gain
BANDGAP AND
TEMPERATURE
SENSOR
VOLTAGE AND
REFERENCE
GENERATOR
1.0V
0.94V
0.9V
operational amplifier driving a PMOS pass transistor. The
design of the ISL9005 provides a regulator that has low
quiescent current, fast transient response, and overall
stability across all operating and load current conditions.
GND
Functional Description
The ISL9005 contains all circuitry required to implement a
high performance LDO. High performance is achieved
through a circuit that delivers fast transient response to
varying load conditions. In a quiescent condition, the
ISL9005 adjusts its biasing to achieve the lowest standby
current consumption.
The device also integrates current limit protection, smart
thermal shutdown protection, and soft-start. Smart Thermal
shutdown protects the device against overheating.
Power Control
The ISL9005 has an enable pin (EN) to control power to the
LDO output. When EN is low, the device is in shutdown
mode. During this condition, all on-chip circuits are off, and
the device draws minimum current, typically less than 0.1μA.
When the enable pin is asserted, the device first polls the
output of the UVLO detector to ensure that VIN voltage is at
least about 2.1V. Once verified, the device initiates a start-up
sequence. During the start-up sequence, trim settings are
first read and latched. Then, sequentially, the bandgap,
reference voltage and current generation circuitry power-up.
Once the references are stable, a fast-start circuit powers up
the LDO.
8
LDO stability is guaranteed for a 1μF to 10μF output
capacitor that has a tolerance better than 20% and ESR less
than 200m Ω . The design is performance-optimized for a 1μF
capacitor. Unless limited by the application, use of an output
capacitor value above 4.7μF is not recommended as LDO
performance improvement is minimal.
Soft-start circuitry integrated into each LDO limits the initial
ramp-up rate to about 30μs/V to minimize current surge. The
ISL9005 provides short-circuit protection by limiting the
output current to about 425mA.
The LDO uses an independently trimmed 1V reference as its
input. An internal resistor divider drops the LDO output
voltage down to 1V. This is compared to the 1V reference for
regulation. The resistor division ratio is programmed in the
factory.
Overheat Detection
The bandgap outputs a proportional-to-temperature current
that is indicative of the temperature of the silicon. This
current is compared with references to determine if the
device is in danger of damage due to overheating. When the
die temperature reaches about +140°C, if the LDO is
sourcing more than 50mA it shuts down until the die cools
sufficiently. Once the die temperature falls back below about
+110°C, the disabled LDO is re-enabled and soft-start
automatically takes place.
FN9234.2
May 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| PSAC60W-560-R-C3 | ADAPTER DESKTOP CLASS II 60W 56V |
| T86E476M020ESAS | CAP TANT 47UF 20V 20% 2917 |
| AMM18DRUH | CONN EDGECARD 36POS .156 DIP SLD |
| PSAC60W-560-R-C2 | ADAPTER DESKTOP CLASS II 60W 56V |
| T86E476K020ESAS | CAP TANT 47UF 20V 10% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9005IRRZ | 制造商:Intersil Corporation 功能描述: |
| ISL9005IRRZ-T | 功能描述:IC REG LDO 2.6V .3A 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:1 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.25 V ~ 10 V 输入电压:2.9 V ~ 12 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:700mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:Digi-Reel® 其它名称:NCV8535MNADJR2GOSDKR |
| ISL9007 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Current LDO with Low IQ and High PSRR |
| ISL9007IUFZ | 功能描述:IC REG LDO 2.5V .4A 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| ISL9007IUFZ-T | 功能描述:IC REG LDO 2.5V .4A 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:2,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5 V 输入电压:2.5 V ~ 7 V 电压 - 压降（标准）:0.24V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:1.2A 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-261-5，TO-261AB 供应商设备封装:SOT-223-5 包装:带卷 (TR) 其它名称:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
发布紧急采购，3分钟左右您将得到回复。