- 您现在的位置：买卖IC网 > PDF目录20689 > ISL9440IRZ (Intersil)IC REG QD BCK/LINEAR SYNC 32-QFN PDF资料下载
参数资料
| 型号： | ISL9440IRZ |
| 厂商： | Intersil |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC REG QD BCK/LINEAR SYNC 32-QFN |
| 产品培训模块： | Solutions for Test and Measurement Equipment Solutions for Industrial Control Applications |
| 标准包装： | 60 |
| 拓扑： | 降压（降压）同步（3），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 4 |
| 频率 - 开关： | 300kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 24 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | * |
| 包装： | 管件 |
| 产品目录页面： | 1244 (CN2011-ZH PDF) |
ISL9440, ISL9440A, ISL9441
Where Q GATE is the amount of gate charge required to fully
charge the gate of the upper MOSFET. The Δ V BOOT term is
defined as the allowable droop in the rail of the upper drive.
As an example, suppose an upper MOSFET has a gate
charge (QGATE) of 25nC at 5V and also assume the droop
in the drive voltage over a PWM cycle is 200mV. One will
find that a bootstrap capacitance of at least 0.125μF is
required. The next larger standard value capacitance is
0.22μF. A good quality ceramic capacitor is recommended.
Protection Circuits
The converter output is monitored and protected against
overload, short circuit and undervoltage conditions. A
sustained overload on the output sets the PGOOD low and
initiates hiccup mode.
Undervoltage Lockout
The ISL9440, ISL9440A and ISL9441 include UVLO
protection that will keep the devices in a reset condition until
a proper operating voltage is applied and that will also shut
down the ISL9440, ISL9440A and ISL9441 if the operating
voltage drops below a pre-defined value. All controllers are
disabled when UVLO is asserted. When UVLO is asserted,
PGOOD will be valid and de-asserted.
Overcurrent Protection
All the PWM controllers use the lower MOSFET’s
on-resistance, r DS(ON) , to monitor the current in the
converter. The sensed voltage drop is compared with a
threshold set by a resistor connected from the OCSETx pin
to ground.
Overvoltage Protection
All switching controllers within the ISL9440, ISL9440A and
ISL9441 have fixed overvoltage set points. The overvoltage
set point is set at 118% of the output voltage set by the
feedback resistors. In the case of an overvoltage event, the
IC will attempt to bring the output voltage back into
regulation by keeping the upper MOSFET turned off and
modulating the lower MOSFET for 2 consecutive PWM
cycles. If the overvoltage condition has not been corrected in
2 cycles, the ISL9440, ISL9440A and ISL9441 will turn on
the lower MOSFET until the overvoltage has been cleared,
or the power path is interrupted by opening a fuse.
Over-Temperature Protection
The IC incorporates an over-temperature protection circuit
that shuts the IC down when a die temperature of +150°C
is reached. Normal operation resumes when the die
temperatures drops below +130°C through the initiation of
a full soft-start cycle.
Feedback Loop Compensation
To reduce the number of external components and to simplify
the process of determining compensation components, all
PWM controllers have internally compensated error
amplifiers. To make internal compensation possible several
design measures were taken.
First, the ramp signal applied to the PWM comparator is
proportional to the input voltage provided via the VIN pin.
This keeps the modulator gain constant with variation in the
input voltage. Second, the load current proportional signal is
derived from the voltage drop across the lower MOSFET
( I OC ) ( r DS ( ON ) )
( 7 ) ( R CS )
R OCSET = -------------------------------------------
(EQ. 5)
during the PWM time interval and is subtracted from the
amplified error signal on the comparator input. This creates
an internal current control loop. The resistor connected to
where, I OC is the desired overcurrent protection threshold,
and R CS is a value of the current sense resistor connected to
the ISENx pin. If an overcurrent is detected for 2 consecutive
clock cycles then the IC enters a hiccup mode by turning off
the ISEN pin sets the gain in the current feedback loop. The
following expression estimates the required value of the
current sense resistor depending on the maximum operating
load current and the value of the MOSFET’s r DS(ON) .
( I MAX ) ( r DS ( ON ) )
the gate drivers and entering into soft-start. The IC will cycle
4 times through soft-start before trying to restart. The IC will
continue to cycle through soft-start until the overcurrent
15 μ A
R CS ≥ -----------------------------------------------
(EQ. 6)
condition is removed. Hiccup mode is active during soft-start
so care must be taken to ensure that the peak inductor
current does not exceed the overcurrent threshold during
soft-start.
Because of the nature of this current sensing technique, and
to accommodate a wide range of r DS(ON) variations, the
value of the overcurrent threshold should represent an
Choosing R CS to provide 15μA of current to the current
sample and hold circuitry is recommended but values down
to 2μA and up to 100μA can be used. The higher sampling
current will help to stabilize the loop.
Due to the current loop feedback, the modulator has a single
pole response with -20dB slope at a frequency determined
by the load.
F PO = ---------------------------------
overload current about 150% to 180% of the maximum
operating current. If more accurate current protection is
desired, place a current sense resistor in series with the
1
2 π ? R O ? C O
(EQ. 7)
lower MOSFET source.
15
where R O is load resistance and C O is load capacitance. For
this type of modulator, a Type 2 compensation circuit is
usually sufficient.
FN6383.1
December 5, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| GBM10DSEH-S243 | CONN EDGECARD 20POS .156 EYELET |
| S2J-E3/5BT | DIODE GPP 1.5A 600V DO-214AA |
| ISL8501IRZ | IC REG TRPL BUCK/LINEAR 24-QFN |
| GEM12DCAT | CONN EDGECARD 24POS R/A .156 SLD |
| EBM06DTBN-S189 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9440IRZ-T | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（2），线性（LDO）（1） 功能:任何功能 输出数:3 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:4.5 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:28-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:* 包装:带卷 (TR) 其它名称:ISL6402IVZ-TTR |
| ISL9441IRZ | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（2），线性（LDO）（1） 功能:任何功能 输出数:3 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:4.5 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:28-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:* 包装:带卷 (TR) 其它名称:ISL6402IVZ-TTR |
| ISL9441IRZ-T | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（2），线性（LDO）（1） 功能:任何功能 输出数:3 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:4.5 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:28-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:* 包装:带卷 (TR) 其它名称:ISL6402IVZ-TTR |
| ISL9443IRZ | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL9443IRZS2750 | 制造商:Intersil Corporation 功能描述:PB FREE. ISL9443 TRIPLE, STEP- DOWN PWM CONTROLLER IMVP-6. 3 - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。