- 您现在的位置：买卖IC网 > PDF目录22323 > ISL9441IRZ-T (Intersil)IC REG QD BCK/LINEAR SYNC 32-QFN PDF资料下载
参数资料
| 型号： | ISL9441IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 18/20页 |
| 文件大小： | 0K |
| 描述： | IC REG QD BCK/LINEAR SYNC 32-QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 6,000 |
| 拓扑： | 降压（降压）同步（3），线性（LDO）（1） |
| 功能： | 任何功能 |
| 输出数： | 4 |
| 频率 - 开关： | 300kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 24 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | * |
| 包装： | 带卷 (TR) |
ISL9440, ISL9440A, ISL9441
Output Capacitor Selection
The output capacitors for each output have unique
requirements. In general, the output capacitors should be
selected to meet the dynamic regulation requirements
including ripple voltage and load transients. Selection of
output capacitors is also dependent on the output inductor,
so some inductor analysis is required to select the output
capacitors.
One of the parameters limiting the converter ’s response to a
(ISL9440/ISL9441)/600kHz (ISL9440A) for the bulk
capacitors. In most cases, multiple small-case electrolytic
capacitors perform better than a single large-case capacitor.
The stability requirement on the selection of the output
capacitor is that the ‘ESR zero’ (f Z ) be between 1.2kHz and
30kHz. This range is set by an internal, single compensation
zero at 6kHz. The ESR zero can be a factor of five on either
side of the internal zero and still contribute to increased
phase margin of the control loop. Therefore:
C OUT = -------------------------------------
load transient is the time required for the inductor current to
slew to it’s new level. The ISL9440, ISL9440A and ISL9441
1
2 Π ( ESR ) ( f Z )
(EQ. 14)
will provide either 0% or maximum duty cycle in response to
a load transient.
The response time is the time interval required to slew the
inductor current from an initial current value to the load
current level. During this interval the difference between the
inductor current and the transient current level must be
supplied by the output capacitor(s). Minimizing the response
time can minimize the output capacitance required. Also, if
the load transient rise time is slower than the inductor
response time, as in a hard drive or CD drive, it reduces the
requirement on the output capacitor.
The maximum capacitor value required to provide the full,
rising step, transient load current during the response time of
In conclusion, the output capacitors must meet three criteria:
1. They must have sufficient bulk capacitance to sustain the
output voltage during a load transient while the output
inductor current is slewing to the value of the load
transient.
2. The ESR must be sufficiently low to meet the desired
output voltage ripple due to the output inductor current.
3. The ESR zero should be placed, in a rather large range,
to provide additional phase margin.
The recommended output capacitor value for the ISL9440,
ISL9440A and ISL9441 is between 150 μ F to 680 μ F, to meet
stability criteria with external compensation. Use of
aluminum electrolytic (POSCAP) or tantalum type capacitors
( L O ) ( I TRAN )
2 ( V IN – V O ) ( DV OUT )
the inductor is:
2
C OUT = -----------------------------------------------------------
(EQ. 12)
is recommended. Use of low ESR ceramic capacitors is
possible but would take more rigorous loop analysis to
ensure stability.
( V IN – V OUT ) ( V OUT )
Δ I L = ----------------------------------------------------------
( f S ) ( L ) ( V IN )
where, C OUT is the output capacitor(s) required, L O is the
output inductor, I TRAN is the transient load current step, V IN
is the input voltage, V O is output voltage, and DV OUT is the
drop in output voltage allowed during the load transient.
High frequency capacitors initially supply the transient
current and slow the load rate-of-change seen by the bulk
capacitors. The bulk filter capacitor values are generally
determined by the ESR (Equivalent Series Resistance) and
voltage rating requirements as well as actual capacitance
requirements.
The output voltage ripple is due to the inductor ripple current
and the ESR of the output capacitors as defined by:
Output Inductor Selection
The PWM converters require output inductors. The output
inductor is selected to meet the output voltage ripple
requirements. The inductor value determines the converter ’s
ripple current and the ripple voltage is a function of the ripple
current and output capacitor(s) ESR. The ripple voltage
expression is given in the capacitor selection section and the
ripple current is approximated by Equation 15:
(EQ. 15)
For the ISL9440, ISL9440A and ISL9441, inductor values
between 1.2μH to 10μH are recommended when using the
V RIPPLE = Δ I L ( ESR )
(EQ. 13)
Typical Application Schematic. Other values can be used but
a thorough stability study should be done. A smaller volume
where, I L is calculated in the “Output Inductor Selection” on
page 18.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load
circuitry for specific decoupling requirements.
Use only specialized low-ESR capacitors intended for
switching-regulator applications at 300kHz
18
cap in combination with big inductor will be more prone to
stability issues. One way to get more phase margin is to add
a small cap (typically 1nF to 10nF) in parallel with the upper
resistor of the voltage sense resistor divider. For example, in
ISL9440, ISL9440A Application Schematic, the 5V output
has a 15μH inductor with which the system phase margin is
less than 45°. An resistor and capacitor are added with the
upper resistor of the divider to get more phase margin.
FN6383.1
December 5, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040C30IDBZR | IC VREF SHUNT PREC 3V SOT-23-3 |
| ISL6549IBZ | IC REG DL BCK/LINEAR 14-SOIC |
| V110C5H75BG3 | CONVERTER MOD DC/DC 5V 75W |
| SE10PG-M3/85A | DIODE ESD 1.0A 400V DO-220AA |
| V110C5H75BG2 | CONVERTER MOD DC/DC 5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL9443IRZ | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL9443IRZS2750 | 制造商:Intersil Corporation 功能描述:PB FREE. ISL9443 TRIPLE, STEP- DOWN PWM CONTROLLER IMVP-6. 3 - Rail/Tube |
| ISL9443IRZ-T | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL9443IRZ-T7A | 功能描述:软开关 PWM 控制器 ISL9443 TRIPLE STEP CONTRLR IMVP-6. 32LD RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| ISL9443IRZ-T7AS2750 | 制造商:Intersil Corporation 功能描述:ISL9443 TRIPLE, STEP- DOWN PWM CONTROLLER IMVP-6. 32 LD MLFP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。