- 您现在的位置：买卖IC网 > PDF目录17236 > ISL97516IUZ-EVALZ (Intersil)EVALUATION BOARD FOR ISL97516IUZ PDF资料下载
参数资料
| 型号： | ISL97516IUZ-EVALZ |
| 厂商： | Intersil |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR ISL97516IUZ |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步升 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 5 ~ 25 V |
| 电流 - 输出： | 1A |
| 输入电压： | 2.3 ~ 5.5 V |
| 稳压器拓扑结构： | 升压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL97516 |
ISL97516
During the second cycle, the power FET turns off and the
Schottky diode is forward biased, (Figure 13). The energy
stored in the inductor is pumped to the output supplying
output current and charging the output capacitor. The Schottky
V IN
C IN
L
D
C OUT
V OUT
Δ I L = Δ t2 × --------------------------------
Δ t2 = -------------
Δ I L2
D V IN 1 – D V IN – V OUT
f SW
f SW
diode side of the inductor is clamp to a Schottky diode above
the output voltage. So the voltage drop across the inductor is
V IN - V OUT . The change in inductor current during the second
cycle is:
V IN – V OUT
L
1 – D
f SW (EQ. 2)
For stable operation, the same amount of energy stored in the
inductor must be taken out. The change in inductor current
during the two cycles must be the same.
Δ I1 + Δ I2 = 0
---------- × --------- + ------------- × -------------------------------- = 0
L L
ISL97516
I L
Δ T 2
Δ V O
FIGURE 13. BOOST CONVERTER - CYCLE 2, POWER SWITCH OPEN
Output Voltage
An external feedback resistor divider is required to divide the
output voltage down to the nominal 1.294V reference voltage.
The current drawn by the resistor network should be limited to
maintain the overall converter efficiency. The maximum value
of the resistor network is limited by the feedback input bias
current and the potential for noise being coupled into the
V OUT 1
V IN
---------------- = -------------
1 – D
(EQ. 3)
feedback pin. A resistor network less than 100k is
recommended. The boost converter output voltage is
determined by the relationship in Equation 4:
V OUT = V FB × ? 1 + ------- ?
L
D
? R 1 ?
? R 2 ?
(EQ. 4)
V IN
C IN
C OUT
V OUT
The nominal VFB voltage is 1.294V.
ISL97516
FIGURE 11. BOOST CONVERTER
Inductor Selection
The inductor selection determines the output ripple voltage,
transient response, output current capability, and efficiency. Its
selection depends on the input voltage, output voltage,
switching frequency, and maximum output current. For most
applications, the inductance should be in the range of 2μH to
33μH. The inductor maximum DC current specification must
be greater than the peak inductor current required by the
I L ( PEAK ) = ------------------------------------ + 1 ? 2 × -----------------------------------------------------
V IN
C IN
L
C OUT
V OUT
regulator. The peak inductor current can be calculated using
Equation 5:
I OUT × V OUT V IN × ( V OUT – V IN )
V IN L × V OUT × FREQ
ISL97516
Output Capacitor
(EQ. 5)
Δ V O
I L
Δ t 1
Δ I L1
Low ESR capacitors should be used to minimize the output
voltage ripple. Multilayer ceramic capacitors (X5R and X7R) are
preferred for the output capacitors because of their lower ESR
and small packages. Tantalum capacitors with higher ESR can
also be used. The output ripple can be calculated in Equation 6:
Δ V O = ------------------------- + I OUT × ESR
FIGURE 12. BOOST CONVERTER - CYCLE 1, POWER SWITCH
CLOSED
I OUT × D
f SW × C O
(EQ. 6)
For noise sensitive applications, a 0.1μF placed in parallel with
the larger output capacitor is recommended to reduce the
switching noise coupled from the LX switching node.
6
FN9261.6
March 28, 2014
相关PDF资料 |
PDF描述 |
|---|---|
| GBC17DRYH | CONN EDGECARD 34POS DIP .100 SLD |
| GBC18DRXS | CONN EDGECARD 36POS DIP .100 SLD |
| GCA24DRMN | CONN EDGECARD 48POS .125 SQ WW |
| GEC22DRTI | CONN EDGECARD 44POS DIP .100 SLD |
| RB-1515D/H | CONV DC/DC 1W 15VIN +/-15VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97516IUZ-T | 功能描述:IC REG BOOST ADJ 1A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:50 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:5 V ~ 25 V 输入电压:2.3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:600kHz，1.2MHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 包装:管件 供应商设备封装:8-MSOP |
| ISL97516IUZ-TK | 功能描述:IC REG BOOST ADJ 1A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1,000 系列:- 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.6 V ~ 4.5 V 输入电压:3 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:3MHz 电流 - 输出:1.5A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:6-LLP-EP（3x3） 产品目录页面:1300 (CN2011-ZH PDF) 其它名称:LM2831ZSDLM2831ZSDTR |
| ISL97519AIUZ | 功能描述:IC REG BOOST ADJ 1A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1 系列:EZBuck™ 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.8 V ~ 22.1 V 输入电压:3 V ~ 26 V PWM 型:电流模式 频率 - 开关:1.5MHz 电流 - 输出:1.8A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 包装:剪切带 (CT) 供应商设备封装:8-DFN（2x2） 其它名称:785-1276-1 |
| ISL97519AIUZEVALZ | 功能描述:EVAL BOARD FOR ISL97519AIUZ RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ISL97519AIUZ-T | 功能描述:IC REG BOOST ADJ 1A 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
发布紧急采购，3分钟左右您将得到回复。