- 您现在的位置：买卖IC网 > Datasheet目录335 > ISL97635IRZ (Intersil)IC LED DRVR WHT/RGB BCKLGT 24QFN Datasheet资料下载
参数资料
| 型号： | ISL97635IRZ |
| 厂商： | Intersil |
| 文件页数： | 19/28页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHT/RGB BCKLGT 24QFN |
| 标准包装： | 75 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 8 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 600kHz，1.2MHz |
| 电源电压： | 6 V ~ 24 V |
| 输出电压： | 34.5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ISL97635
TABLE 2B. DATA BIT DESCRIPTIONS
ADDRESS
REGISTER
DATA BIT DESCRIPTIONS
0x00
PWM Brightness Control Register BRT[7..0] = 256 steps of DPWM duty cycle brightness control
0x01
Device Control Register
PWM_MD = PWM mode select bit (1 = absolute brightness, 0 = % change), default = 0
PWM_SEL = Brightness control select bit (1 = control by PWMI, 0 = control by SMBus), default = 0
BL_CTL = BL On/Off (1 = On, 0 = Off), default = 0
PWM_MD PWM_SEL
MODE
X
1
0
1
0
0
PWMI Mode
SMBus Mode
SMBus and PWMI mode with DPST
0x02
0x03
0x07
0x08
Fault/Status Register
Identification Register
DC Brightness Control Register
Configuration Register
2_CH_SD = Two LED output channels are shutdown (1 = shutdown, 0 = OK)
1_CH_SD = One LED output channel is shutdown (1 = shutdown, 0 = OK)
BL_STAT = BL status (1 = BL On, 0 = BL Off)
OV_CURR = Input overcurrent (1 = Overcurrent condition, 0 = Current OK)
THRM_SHDN = Thermal Shutdown (1 = Thermal fault, 0 = Thermal OK)
FAULT = Fault occurred (Logic “OR” of all of the fault conditions)
MFG[3..0] = Manufacturer ID (16 vendors available. Intersil is vendor ID 9)
REV[2..0] = Silicon rev (Rev 0 through Rev 7 allowed for silicon spins)
BRTDC[7..0] = 256 steps of DC brightness control
VSC[1..0] = Short circuit thresholds selection
FSW[2] = Switching frequencies selection
VSC1
0
1
1
VSC0
X
0
1
OPERATION
No VSC error detection
VSC = 3.1V ±15%
VSC = 8V ±15%
f SW
0
1
OPERATION
f SW = 600kHz
f SW = 1.2MHz
0x09
Output Channel Mask/Fault
Readout Register
CH[5..0] = Output Channel Read and Write. In Write, 1 = Channel Enabled, 0 = Channel Disabled.
In Read, 1 = Channel OK, 0 = Channel Not OK/Channel disabled
PWM Brightness Control Register (0x00)
The Brightness control resolution has 256 steps of PWM duty
cycle adjustment. The bit assignment is shown in Figure 23. All
of the bits in this Brightness Control Register can be read or
write. Step 0 corresponds to the minimum step where the
current is less than 10μA. Steps 1 to 255 represent the linear
steps between 0.39% and 100% duty cycle with approximately
0.39% duty cycle adjustment per step.
? An SMBus Write Byte cycle to Register 0x00 sets the
PWM brightness level only if the backlight controller is in
SMBus mode (see Table 3 Operating Modes selected by
Device Control Register Bits 1 and 2).
? An SMBus Read Byte cycle to Register 0x00 returns the
programmed PWM brightness level, regardless of the
value of PWM_SEL.
19
? An SMBus setting of 0xFF for Register 0x00 sets the
backlight controller to the maximum brightness.
? An SMBus setting of 0x00 for Register 0x00 sets the
backlight controller to the minimum brightness output in
which the LED current is guaranteed to be less than 10μA.
? Default value for Register 0x00 is 0xFF.
Device Control Register (0x01)
This register has 2 bits that control the operating mode of the
backlight controller and a single bit that controls the BL
ON/OFF state. The remaining bits are reserved. The bit
assignment is shown in Figure 24. All other bits in the Device
Control Register will read as low unless otherwise written.
Bits 7 and 6 are not implemented and will always read low.
FN6434.2
December 22, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97636AIRZ | IC LED DRIVR WHITE BCKLGT 24-QFN |
| ISL97636IRZ-TK | IC LED DRIVR WHITE BCKLGT 24-QFN |
| ISL97671AIRZ | IC LED DVR PWM CTRL 6CH 20QFN |
| ISL97672AIRZ | IC LED DRVR LOW DIMMING 20QFN |
| ISL97672BIRZ | IC LED DRVR BACKLIGHT 20QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97635IRZ-T | 功能描述:IC LED DRVR WHT/RGB BCKLGT 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97635IRZ-TK | 功能描述:IC LED DRVR WHT/RGB BCKLGT 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97636AIRZ | 功能描述:LED照明驱动器 6-CH LED DRVR RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| ISL97636AIRZ-T | 功能描述:IC LED DRIVR WHITE BCKLGT 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97636AIRZ-TK | 功能描述:IC LED DRIVR WHITE BCKLGT 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
发布紧急采购，3分钟左右您将得到回复。