参数资料
| 型号： | ISL97644IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST LDO VON VCOM 24-QFN |
| 标准包装： | 6,000 |
| 应用： | LCD 监视器，笔记本电脑显示器 |
| 电流 - 电源： | 1mA |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
ISL97644
Low to high transition is determined primarily by the switch
resistance and the external capacitive load. High to low
transition is more complex. Take the case where the block is
and inductor to disconnect the DC path when the part is
disabled.
already enabled (VDPM is H). When VFLK is H, pin CE is
grounded. On the falling edge of VFLK, a current is passed
into pin CE, to charge an external capacitor to 1.2V. This
creates a delay, equal to CE*4200. At this point, the output
begins to pull down from VGH to VDD1. The slew current is
TO INDUCTOR
INPUT
equal to 300/(RE+5000)*Load Capacitance.
VDPM
0
ENABLE
FIGURE 19. CIRCUIT TO DISCONNECT THE DC PATH OF
BOOST CONVERTER
VFLK
VGH_M
0
SLOPE CONTROLLED
BY RE AND LOAD
CAPACITANCE
VGH
V COM Amplifier
The V COM amplifier is designed to control the voltage on the
back plate of an LCD display. This plate is capacitively
coupled to the pixel drive voltage which alternately cycles
VDD_1
0
DELAY TIME
CONTROLLED BY CE
FIGURE 17. GATE PULSE MODULATOR TIMING DIAGRAM
Start-Up Sequence
Figure 18 shows a detailed start up sequence waveform.
V IN
0
ENABLE
positive and negative at the line rate for the display. Thus the
amplifier must be capable of sourcing and sinking capacitive
pulses of current, which can occasionally be quite large (a
few 100mA for typical applications).
The ISL97644 V COM amplifier's output current is limited to
400mA. This limit level, which is roughly the same for
sourcing and sinking, is included to maintain reliable
operation of the part. It does not necessarily prevent a large
temperature rise if the current is maintained. (In this case the
whole chip may be shut down by the thermal trip to protect
functionality.) If the display occasionally demands current
pulses higher than this limit, the reservoir capacitor will
provide the excess and the amplifier will top the reservoir
capacitor back up once the pulse has stopped. This will
happen on the μs time scale in practical systems and for
0
VIN THRESHOLD
pulses 2 or 3 times the current limit, the V COM voltage will
have settled again before the next line is processed.
VDPM
0
Fault Protection
ISL97644 provides the overall fault protections including
over current protection and over-temperature protection.
0
AVDD
LDO OUTPUT
VGH_M
An internal temperature sensor continuously monitors the
die temperature. In the event that die temperature exceeds
the thermal trip point, the device will shut down and disable
itself. The upper and lower trip points are typically set to
FIGURE 18. START-UP SEQUENCE
When V IN exceeds 2.5V and ENABLE reaches the VIH
threshold value, Boost converter and LDO start up, and gate
pulse modulator circuit output holds until VDPM goes to
high. Note that there is a DC path in the boost converter from
the input to the output through the inductor and diode, hence
the input voltage will be seen at output with a forward voltage
drop of diode before the part is enabled. If this voltage is not
desired, the following circuit can be inserted between input
13
+140°C and +100°C respectively.
FN9228.1
December 14, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97645AIRZ | IC REG BOOST VON VCOM 24-QFN |
| ISL97646IRZ-TK | IC REG BOOST LDO VON VCOM 24-QFN |
| ISL97649AIRZ | IC POWER MANAGEMENT |
| ISL97649BIRZ | IC POWER MANAGEMENT |
| ISL97650ARTZ-T | IC LCD SUPPLY HP 4CHN 36-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97644IRZ-TK | 功能描述:IC REG BOOST LDO VON VCOM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL97645AIRZ | 功能描述:IC REG BOOST VON VCOM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL97645AIRZ-T | 功能描述:IC REG BOOST VON VCOM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL97645AIRZ-TK | 功能描述:IC REG BOOST VON VCOM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL97645IRZ-T | 功能描述:IC REG BOOST VON VCOM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。