- 您现在的位置：买卖IC网 > Datasheet目录335 > ISL97677IRZ (Intersil)IC LED DVR PWM CTRL 8CH 32QFN Datasheet资料下载
参数资料
| 型号： | ISL97677IRZ |
| 厂商： | Intersil |
| 文件页数： | 20/23页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR PWM CTRL 8CH 32QFN |
| 标准包装： | 60 |
| 拓扑： | 线性（LDO），PWM，升压（升压） |
| 输出数： | 8 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 500kHz ~ 1.5MHz |
| 电源电压： | 4.75 V ~ 26 V |
| 输出电压： | 45V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
ISL97677
Since the voltage across an inductor is as shown in
Equation 7:
It is recommended that an input capacitor of at least
10μF be used. Ensure the voltage rating of the input
V L = L × Δ I L ? Δ t
and Δ I L @ On = Δ I L @ Off, therefore:
( V I – 0 ) ? L × D × t S = ( V O – V D – V I ) ? L × ( 1 – D ) × t S
(EQ. 7)
(EQ. 8)
capacitor is suitable to handle the full supply range.
Inductor
The selection of the inductor should be based on its
maximum and saturation current (I SAT ) characteristics,
power dissipation (DCR), EMI susceptibility (shielded vs
V O ? V I = 1 ? ( 1 – D )
D = ( V O – V I ) ? V O
where D is the switching duty cycle defined by the
turn-on time over the switching periods. V D is Schottky
diode forward voltage that can be neglected for
approximation.
Rearranging the terms without accounting for V D gives
the boost ratio and duty cycle respectively as Equations 9
and 10:
(EQ. 9)
(EQ. 10)
Input Capacitor
Switching regulators require input capacitors to deliver
peak charging current and to reduce the impedance of
the input supply. This reduces interaction between the
regulator and input supply, thereby improving system
stability. The high switching frequency of the loop causes
almost all ripple current to flow in the input capacitor,
which must be rated accordingly.
A capacitor with low internal series resistance should be
chosen to minimize heating effects and improve system
efficiency, such as X5R or X7R ceramic capacitors, which
offer small size and a lower value of temperature and
voltage coefficient compared to other ceramic capacitors.
PWM BRIGHTNESS CONTROL
unshielded), and size. Inductor type and value influence
many key parameters, including ripple current, current
limit, efficiency, transient performance and stability.
The inductor’s maximum current capability must be
adequate enough to handle the peak current at the worst
case condition. Additionally if an inductor core is chosen
with too low a current rating, saturation in the core will
cause the effective inductor value to fall, leading to an
increase in peak to average current level, poor efficiency
and overheating in the core. The series resistance, DCR,
within the inductor causes conduction loss and heat
dissipation. A shielded inductor is usually more suitable
for EMI susceptible applications, such as LED
backlighting.
The peak current can be derived from the voltage across
the inductor during the Off-period, as expressed in
Equation 11:
IL peak = ( V O × I O ) ? ( 85% × V I ) + 1 ? 2 [ V I × ( V O – V I ) ? ( L × V O × f SW )
(EQ. 11)
The choice of 85% is just an average term for the
efficiency approximation. The first term is the average
current, which is inversely proportional to the input
voltage. The second term is the inductor current change,
which is inversely proportional to L and f SW . As a result,
for a given switching.
REGISTER 0x00
REGISTER
BRT7
BRT6
BRT5
BRT4
BRT3
BRT2
BRT1
BRT0
Bit 7 (R/W) Bit 6 (R/W) Bit 5 (R/W) Bit 4 (R/W) Bit 3 (R/W) Bit 2 (R/W) Bit 1 (R/W) Bit 0 (R/W)
BIT ASSIGNMENT
BRT[7..0]
BIT FIELD DEFINITIONS
= 256 steps of PWM brightness levels
FIGURE 30. DESCRIPTIONS OF BRIGHTNESS CONTROL REGISTER
20
FN6996.1
November 13, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97678IRZ | IC LED DVR PWM DIMMING 8CH 32QFN |
| ISL97686IRTZ | IC LED DRVR BACKLIGHT 28TQFN |
| ISL97691IRTZ-TK | IC LED DRVR BACKLIGHT 3D 16TQFN |
| ISL97693IRTZ-TK | IC LED DRVR BACKLIGHT 16TQFN |
| ISL97901CRZ | IC LED DRVR 1.5A 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97677IRZ-T | 功能描述:IC LED DVR PWM CTRL 8CH 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97677IRZ-TK | 功能描述:IC LED DVR PWM CTRL 8CH 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97678IRZ | 功能描述:IC LED DVR PWM DIMMING 8CH 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| ISL97678IRZ-T | 功能描述:IC LED DVR PWM DIMMING 8CH 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97678IRZ-TK | 功能描述:IC LED DVR PWM DIMMING 8CH 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
发布紧急采购，3分钟左右您将得到回复。