- 您现在的位置：买卖IC网 > PDF目录20788 > ISL97682IRTZ (Intersil)IC LED DVR PWM CTRL 2CH 16TQFN PDF资料下载
参数资料
| 型号： | ISL97682IRTZ |
| 厂商： | Intersil |
| 文件页数： | 10/17页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR PWM CTRL 2CH 16TQFN |
| 标准包装： | 100 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 频率： | 500kHz ~ 650kHz，900kHz ~ 1.1MHz |
| 电源电压： | 4 V ~ 26.5 V |
| 输出电压： | 45V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN（3x3） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
ISL97682, ISL97683, ISL97684
Theory of Operation
PWM Boost Converter
The current mode PWM boost converter produces the minimal
voltage needed to enable the LED stack with the highest forward
voltage drop to run at the programmed current. The ISL97682,
ISL97683, ISL97684 employs current mode control boost
architecture that has a fast current sense loop and a slow voltage
feedback loop. Such architecture achieves a fast transient
response that is essential for the notebook backlight application
where the power can be a series of drained batteries or instantly
change to an AC/DC adapter without rendering a noticeable
visual nuisance. The number of LEDs that can be driven by the
ISL97682, ISL97683, ISL97684 depend on the type of LED
chosen in the application. The ISL97682, ISL97683, ISL97684
are capable of boosting up to 45V and typically driving 13 LEDs
in series for each of the 4 channels, enabling a total of 52 pieces
of the 3.2V/20mA type of LEDs.
OVP
The Overvoltage Protection (OVP) pin has a function of setting the
Current Matching and Current Accuracy
Each channel of the LED current is regulated by the current
source circuit, as shown in Figure 19.
The LED peak current is set by translating the R SET current to the
output with a scaling factor of 401.8/R SET . The source terminals
of the current source MOSFETs are designed to run at 500mV to
optimize power loss versus accuracy requirements. The sources
of errors of the channel-to-channel current matching come from
the op amps offset, internal layout, reference, and current source
resistors. These parameters are optimized for current matching
and absolute current accuracy. However, the absolute accuracy is
additionally determined by the external R SET . A 1% tolerance
resistor is recommended.
-
overvoltage trip level as well as limiting the V OUT regulation
range.
The ISL97682, ISL97683, ISL97684 OVP threshold is set by
R UPPER and R LOWER shown by Equation 1:
(EQ. 1)
V OUT_OVP = 1.22V * (R UPPER + R LOWER )/R LOWER
RSET
+
REF
+
-
V OUT can only regulate between 42% and 100% of the V OUT_OVP
such that:
Allowable V OUT = 42% to 100% of V OUT_OVP
For example, if 10 LEDs are used with the worst case being V OUT
of 35V. If R 1 and R 2 are chosen such that the OVP level is set at
40V, then the V OUT is allowed to operate between 16.8V and 40V.
If the requirement is changed to 4 LEDs of 14V V OUT application,
then the OVP level must be reduced and users should follow the
V OUT = (42% ~100%) OVP level requirement. Otherwise, the
headroom control will be disturbed such that the channel voltage
can be much higher than expected and sometimes can prevent
the driver from operating properly.
The ratio of the OVP capacitor should be the inverse of the OVP
resistor. For example:
if R UPPER /R LOWER = 33/1, then C UPPER /C LOWER = 1/33 with
C UPPER = 100pF and C UPPER = 3.3nF.
Enable
An EN signal is required to enable the internal regulator for normal
operation. If there is no signal for longer than 28ms, the device will
enter shutdown.
Power Sequence
There is no specific power sequence requirement for the
ISL97682, ISL97683, ISL97684. The EN signal can be tied to V IN
but not the VDC that will prevent the device from powering up.
10
PWM DIMMING
FIGURE 19. SIMPLIFIED CURRENT SOURCE CIRCUIT
Dynamic Headroom Control
The ISL97682, ISL97683, ISL97684 feature a proprietary
Dynamic Headroom Control circuit that detects the highest
forward voltage string or the lowest voltage from any of the CH
pins digitally. When the lowest CH voltage is lower than the short
circuit threshold (V SC ), such voltage will be used as the feedback
signal for the boost regulator. The boost makes the output to the
correct level such that the lowest CH is at the target headroom
voltage. Since all LED stacks are connected to the same output
voltage, the other CH pins will have a higher voltage, but the
regulated current source circuit on each channel will ensure that
each channel has the same current. The output voltage will
regulate cycle-by-cycle and it is always referenced to the highest
forward voltage string in the architecture.
Dimming Controls
The ISL97682, ISL97683, ISL97684 allow two ways of controlling
the LED current, and therefore, the brightness. They are:
1. DC current adjustment
2. PWM chopping of the LED current defined in Step 1.
There are various ways to achieve DC or PWM current control,
which will be described in the following.
FN7689.1
May 16, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| ISL97682IRTZ-T | IC LED DVR PWM CTRL 2CH 16TQFN |
| EEC18DRYH | CONN EDGECARD 36POS DIP .100 SLD |
| EBC10DRTI | CONN EDGECARD 20POS DIP .100 SLD |
| EBC13DREN | CONN EDGECARD 26POS .100 EYELET |
| EBC13DREH | CONN EDGECARD 26POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL97682IRTZEVALZ | 功能描述:EVAL BOARD FOR ISL97682 RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ISL97682IRTZR5509 | 功能描述:LED照明驱动器 1 Channel LED Drivers, 16LD TQFN 3X3 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| ISL97682IRTZ-T | 功能描述:IC LED DVR PWM CTRL 2CH 16TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| ISL97682IRTZ-TK | 功能描述:IC LED DVR PWM CTRL 2CH 16TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| ISL97682IRTZ-TR5509 | 功能描述:LED照明驱动器 1 Channel LED Driver, 16LD TQFN 3X3, T&R RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。