- 您现在的位置：买卖IC网 > Datasheet目录450 > ITR20510/TR8 (Everlight Electronics Co Ltd)OPTO INTERRUPTER Datasheet资料下载
参数资料
| 型号： | ITR20510/TR8 |
| 厂商： | Everlight Electronics Co Ltd |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | OPTO INTERRUPTER |
| 标准包装： | 500 |
| 检测方法： | 反射 |
| 电压 - 集电极发射极击穿（最大）： | 30V |
| 电流 - 集电极 (Ic)（最大）： | 50mA |
| 电流 - DC 正向(If)： | 50mA |
| 输出类型： | 光电晶体管 |
| 响应时间： | 20µs，20µs |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 4-SMD，鸥翼型 |
| 包装： | 带卷 (TR) |
| 工作温度： | -25°C ~ 85°C |
DATASHEET
ITR20510/TR8
Recommended Method of Storage
The following are general recommendations for moisture sensitive level (MSL) 4 storage and use:
?
?
?
?
?
?
Shelf life in sealed bag: 12 months at < 40 °C and < 90% relative humidity (RH)
After bag is opened, devices that will be subjected to reflow solder or other high temperature process must
a) Mounted within 72 hours of factory conditions < 30 °C/60%RH, or
b) Stored at <20% RH
Devices require bake, before mounting, if:
Humidity Indicator Card is > 20% when read at 23 ± 5 °C
If baking is required, devices may be baked:
a) 192 hours at 40 ℃ ,and <5% RH(dry air/nitrogen) or
b) 96 hours at 60 ℃ , and <5% RH for all device containers
c) 24 hours at 125 °C
Soldering Condition
a) Pb-free solder temperature profile
b) Reflow soldering should not be done more than two times.
c) When soldering, do not put stress on the LEDs during heating.
d) After soldering, do not warp the circuit board.
Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.
Revision Copyright ?
10 : (4)
No: Release Date:
2010, Everlight All Rights Reserved. Release Date : June.11.2013. Issue DRX-0000057 Rev4
www.everlight.com
LifecyclePhase:
Expired Period: Forever
相关PDF资料 |
PDF描述 |
|---|---|
| ITR8307/F43 | OPTO INTERRUPTER |
| ITR8307/L24/F43 | OPTO INTERRUPTER |
| ITR8307 | OPTO INTERRUPTER |
| ITR9904 | OPTO INTERRUPTER |
| ITR9909 | OPTO INTERRUPTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ITR20607 | 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:Opto Interrupter |
| ITR20904 | 制造商:Everlight Electronics Co 功能描述: 制造商:Everlight Electronics Co 功能描述:Side Looking Reflective Sensor 3 Pin |
| ITR230C-A.PDF | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| ITR300 | 制造商:JAMECO VALUEPRO 功能描述:POWER TRANSFORMER,ISOLATION,120VAC/120VAC,300VA |
| ITR8010 | 功能描述:OPTO INTERRUPTER RoHS:是 类别:传感器，转换器 >> 光学 - 光断续器 - 槽型 - 晶体管输出 系列:- 产品变化通告:Internal Chip Change 04/May/2007 标准包装:100 系列:- 检测距离:0.063"（1.6mm） 检测方法:可传导的 输出配置:光电晶体管 电流 - DC 正向(If):50mA 电流 - 集电极 (Ic)（最大）:20mA 电压 - 集电极发射极击穿（最大）:35V 响应时间:35µs，35µs 安装类型:通孔 封装/外壳:PCB 安装 包装:管件 类型:无放大 工作温度:-25°C ~ 85°C 其它名称:425-1978-5 |
发布紧急采购，3分钟左右您将得到回复。