- 您现在的位置：买卖IC网 > PDF目录1357 > JBXEP2G16FQSDS (Souriau Connection Technology)CONN RCPT 16POS REAR MNT RA SKT PDF资料下载
参数资料
| 型号： | JBXEP2G16FQSDS |
| 厂商： | Souriau Connection Technology |
| 文件页数： | 26/47页 |
| 文件大小： | 0K |
| 描述： | CONN RCPT 16POS REAR MNT RA SKT |
| 标准包装： | 1 |
| 系列： | JBX |
| 连接器类型： | 插座，母形插口 |
| 位置数： | 16 |
| 外壳尺寸 - 插件： | 2 |
| 安装类型： | 面板安装，隔墙式，直角 |
| 端子： | 焊接 |
| 紧固型： | 推挽式 |
| 方向： | G |
| 防护等级： | IP40 |
| 外壳材料，表面处理： | 黄铜，镍上镀铬 |
| 触点表面涂层： | 金 |
| 特点： | 屏蔽 |
| 包装： | 散装 |
| 触点涂层厚度： | 19.7µin（0.50µm） |
| 额定电流： | 6A |
| 电压 - 额定： | 730VDC |
| 工作温度： | -50°C ~ 125°C |
| 配套产品： | SOU1830-ND - CONN PLUG 16POS STRGHT PIN SLD SOU1722-ND - CONN PLUG 16POS STR CABLE SOLDER |
| 相关产品： | SOU1623-ND - CONN WASHER SIZE 2 INSULATE BLK |
| 其它名称： | SOU1820 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
JBX Series
Push-Pull Connectors
Plug assembly instructions
8. Take the collet that is pre-loaded on the cable and align the slots in the collet with the keys on the end of the half bushings (you
may need to move the braid away from the slots and spin the collet slightly). Once they are aligned, compress the assembly
so that it is in line and there are no gaps between the collet & the half bushings. The braid should still be in place once the
assembly is inserted.
9. Take a connector housing (#7) and slide it over the insulator so that the red dot on the connector housing lines up with the key
on the half bushing with window. Push the whole assembly into the connector housing until it bottoms out. Insure that the keys
are seated properly by turning the collet that is already aligned with the half bushings. If the collet does not turn, then the keys
are correctly aligned. If the collet does turn, then you must withdraw the assembly & realign the keys.
10. Once the assembly is installed into the connector housing and is aligned properly, apply thread lock to thread area. Then slide
the back nut up until you can manually start the back nut threads onto the threaded end of the connector housing. Tighten the
back nut up as far as you can by hand, then take the appropriate wrenches and place the wrenches onto the flats located on
the connector housing. Do not over torque back nut as it can cause connector failure.
11.
12.
If the connector requires a protective boot, slide the boot over the lip on the back nut.
Potting of backend of plug with clipped contacts:
Clipped contacts are designed to float in the connector so that they self align when mated. It is sometimes necessary to pot
the back end of the connector so that the contacts are sealed off from the environment. When this application is needed, it's
recommended that the assembler engage a mating connector/alignment tool to the assembly being potted. Once the mating
connector/alignment tool is engaged, it must be left engaged until the potting compound has hardened. This will insure that
the true position requirements are met. If the application is for low volume, a mating connector can be used. If the application
is for high volume, it is recommended that an alignment tool be purchased from the supplier..
Trouble shooting
Problem:
Contact will not seat in connector, contact
backing out.
Bent solder contact
Connector will not release from mating part
or operate correctly
Over tightened the back nut
Collet will not grip cable
Connector will not assemble
Contact stubbing after mating
Electrical failure
Cause:
Wrong wire or insulation size, wrong strip
length, poor crimping, broken clips, damaged
insulator, removed contact without proper
removal tool, bad crimp.
Bent in handling, bent in soldering operation,
connector assembled incorrectly.
Pins and insulator were inserted into electri-
cal test while unprotected by shell
Not using flats on latching sleeve and back
nut to torque connector, improper assembly
of the connector, over mold material inside
connector
Connector will not release from mating part
or operate correctly, damage connector
Loose cable in connector
Incorrect alignment of key in connector,
half bushings, connector housing, insulator,
collet, braid in key slots in collet
Bent contact and damaged contact,
connector assembled incorrectly
Improper crimping, wrong wire strip length,
wire loading incorrect location, poor solder
joint
26
Correction:
Use correct wire, adjust strip length, strip and
recrimp with the new contact, replace insula-
tor using wrong crimp tool, replace contact
Replace insert with contacts
Release back-nut and re-torque, disassemble
and reassemble, replace connector
Loosen back nut and retighten
Check correct collet size is being used
Disassemble connector and reassemble
connector-aligning keys, relocate braid in
collet
Re- align contact, replace insert with
contacts.
Remove contact with correct removal tool,
reinstall new contact, and verify strip length
相关PDF资料 |
PDF描述 |
|---|---|
| JC26C2-DSM16E | CONN COMPACT FLASH RIGHT EJECTOR |
| JC26C2-DSR16E | CONN COMPACT FLASH RIGHT EJECTOR |
| JC26C2-FSRE | CONN COMPACT FLASH RIGHT EJECTOR |
| JC26E-BB-E1050E | CONN HEADER COMPACT FLASH R/A |
| JC26E-BB13E | CONN RCPT COMPACT FLASH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| JBXEP2G16FSNDS | 制造商:SOURIAU 功能描述:CONN PLUG 16POS FMALE SOLDER |
| JBXEP2G16FSSDS | 功能描述:环形推拉式连接器 16P Socket Recept Solder Panel Mt Sz 2 RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| JBXEP2G18FCSDS | 功能描述:环形推拉式连接器 18P Socket Recept Crimp Panel Mnt Sz 2 RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| JBXEP2G18FPSDS | 功能描述:环形推拉式连接器 18P Socket Recept Strt PCB Shell Sz 2 RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| JBXEP2G18FSSDS | 功能描述:环形推拉式连接器 18P Socket Recept Solder Panel Mt Sz 2 RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
发布紧急采购，3分钟左右您将得到回复。