参数资料
| 型号： | JR16WCCA-8 |
| 厂商： | Hirose Electric Co Ltd |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | CONN STRAIN RELIEF JR16 8MM |
| 产品目录绘图： | JR Series Simple Cord Clamp |
| 标准包装： | 20 |
| 系列： | JR-W |
| 附件类型： | 应力消除 |
| 适用于相关产品： | JR-W 和 RM-W 系列 IDC 连接器 |
| 外壳尺寸 - 插件： | 16 |
| 特点： | 防水 |
| 颜色： | 黑 |
| 其它名称： | *JR16WCCA-8 HR1005 |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
JR-W Series ● IP67 waterproof protected heavy duty metal shell connectors
■ Plug assemblies procedure
Table 1(Solder type)
[Unit:mm] Table 2 Tightning torque[Unit:N·m]
Shell size
13
16
21
25
A
(3)
(3)
(3)
(3)
B
(12)
(14)
(17)
(20)
C
37 or below
39 or below
42 or below
37 or below
Shell size
13
16
21
25
C
2 to 2.5
3 to 3.5
4 to 4.5
5 to 5.5
■ Work procedure
1.Disassembly of connector
(1)To remove the plug, remove the set screw, ?t a receptacle adaptive to the P shell unit to ?x, and remove he cord tube.
(2)To remove the cord clamp, remove the cord tightening screws.
2.Connection
2.1 Soldering type
(1)Use the cable so that the conductor can be soldered properly into the solder cup with the cable sheath diameter adaptive to each cord
clamp.
(2)After the terminal treatment of the cable with a size given in Table 1, thread on the ccable the clamp, washer, gasket, cord tube and
coupling in this order and direction as shown above.
(3) Solder to connect the conductors to the terminals of the P shell unit. Shrinkable tube is recommended to be used at the connecting
part because insulating performance might deteriorate due to solder whiskers or dewing. After connecting, adjust to meet the C size.
(Note2)
3.Assembly of connector
(1)Fit the connected P shell unit to the receptacle ?xed with a vice or the like. Torque the cord tube to the level as given in Table3.
(2)Fit the gasket, washer and clamp. Torque the clamp to the level as given in Table3 while preventing the cable from being ratated. And,
Loctite Japan Co Ltd. is recommended to be applied as locking.(Note3)
(3)Torque the set screw to 0.2 to 0.25 N·m.
(4)Torque the cord tightening screw(two positions) to 0.65 to 0.7 N·m.(Note 4)
Note2. keep the size until assembling is completed
Note3. After tightening, check water proof performance before using.
Note4. Check the clamp strenrth before using.
144
相关PDF资料 |
PDF描述 |
|---|---|
| MC74VHCT50AMEL | IC BUFF/LVL SHFTR N-INV 14SOEIAJ |
| OSTEV116151 | CONN PLUG HEADER 11PS 10.16MM |
| GMA.3B.070.DG | STRAIN RELIEF 7.0MM DIA GRAY |
| MC74VHCT50AM | IC BUFF/LVL SHFTR N-INV 14SOEIAJ |
| GMA.3B.070.DN | STRAIN RELIEF 7.0MM DIA BLACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| JR16WCCA-8(71) | 功能描述:电缆固定件和配件 STRAIN RELEF JR16 8P RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| JR16WCCA-8(72) | 功能描述:标准环形连接器 CABLE CLAMP 8MM RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值: |
| JR16WP-10P | 功能描述:CONN PLUG WATERPROOF 10POS MALE RoHS:否 类别:连接器，互连式 >> 圆形 系列:JR-W 产品目录绘图:63000 Series 63000 Series Front 63000 Series Side 63000 Series Cable End 63000 Series Assembly In Line 6P Mating Face 标准包装:500 系列:63000 连接器类型:插孔，母插口 位置数:6 外壳尺寸 - 插件:迷你型 DIN 外壳尺寸，MIL:- 安装类型:自由悬挂 端子:焊接 紧固型:推挽式 方向:带标记 防护等级:- 外壳材料，表面处理:青铜，镀镍 触点表面涂层:- 特点:- 包装:散装 触点涂层厚度:- 额定电流:- 电压 - 额定:- 工作温度:-40°C ~ 85°C 其它名称:275-1037 |
| JR16WP-10P(71) | 功能描述:标准环形连接器 PLUG IP67 10POS MALE RoHS:否 制造商:Hirose Connector 系列:EM-W 产品类型:Accessories 位置/触点数量:1 触点类型: 触点电镀: 安装风格:Cable 外壳材质: 端接类型:Clamp 电压额定值: |
| JR16WP-10PC | 功能描述:CONN PLUG WATERPROOF 10POS MALE RoHS:否 类别:连接器，互连式 >> 圆形 - 外壳 系列:JR-W 标准包装:1 系列:军用, MIL-DTL-38999 系列 III, ACT 连接器类型:母触点插座 位置数:5 外壳尺寸 - 插件:15-5 外壳尺寸，MIL:D 触点类型：:压接 触点尺寸:16 安装类型:面板安装，隔墙式（前端螺母） 紧固型:有螺纹 方向:N（正常型） 外壳材料，表面处理:合成物，草绿色镉镀层 防护等级:抗环境影响 特点:屏蔽 包装:散装 请注意:不提供触点 其它名称:DD38999/24JD5BN |
发布紧急采购，3分钟左右您将得到回复。