参数资料
| 型号： | KBS-23DA-4A |
| 厂商： | AVX Corporation |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | BUZZER PIEZO ELEMENT 4KHZ 23MM |
| 标准包装： | 100 |
| 系列： | KBS, Kyocera |
| 频率： | 4kHz |
| 类型： | 标准 |
| 阻抗： | 600 欧姆 |
| 电容 @ 频率： | 12000pF @ 1kHz |
| 尺寸： | 0.91 英寸直径（23mm） |
| 端子： | 无 |
3
Piezoelectric Acoustic Generators
Mounting
The various mounting methods for piezoelectric acoustic
elements are discussed below:
Simple Mounting Method
The simplest method is to stick the piezo acoustic element
to the plate using double-sided adhesive tape. However, the
sound pressure will not be optimum.
Circumference Fixing Method
This method is to fix the outside circumference of the
element to the supporting ring of the plate. Considerable sound
pressure can be obtained covering a wide frequency range
around the resonant frequency.
Nodal Mounting Method
This method is to fix the nodal diameter of the element to
the supporting ring of the plate. Loud sound pressure can be
obtained at the resonant frequency. The sound pressure will
drastically drop when the frequency is shifted from the
resonant frequency.
Designing the Fixture
Factors affecting the sound pressure of the piezoelectric
acoustic element are as follows:
1) resonance frequency of the element
2) cavity resonance (cavity design of the case/casing
method)
3) resonance of sound body (mass after casing)
Maximum sound pressure level can be achieved at the
point where the 3 factors overlap. Taking the oscillation
frequency fluctuation into consideration, the fixture is designed
so that peak points are slightly overlapping with one another.
Case Design for Circumference Mounting Method
When designing a case for circumference mounting, the
cavity resonant frequency of the case (fo) is determined by the
following formula:
For example, when KBS-35DA-3A (resonant frequency
fr=2.9
± 0.5 kHz) is mounted in a case where the size is:
D=33.5mm, d=5.5mm,T=2mm, t=1mm, the formula for f
0
is
explained as follows:
Then, the cavity resonant frequency shall be 2,807 Hz.
PIEZOELECTRIC ELEMENT
BAKELITE OR ACRYL RESIN PLATE
SUPPORTING RINGMMMMMMMMMMMMMM
2π
CS
f0
V(t+1.5
)
π
S
(Hz)
where:
V:
cavity volume (m3)
S:
area of open hole
(m2)
t:
Length of open hole
(m)
C:
sound velocity
C=344 m/sec
V
πD2T
4
S
πd2
4
figure 5
figure 6
figure 8
figure 7
PIEZOELECTRIC ELEMENT
BAKELITE OR ACRYL RESIN PLATE
PIEZOELECTRIC ELEMENT
SUPPORTING RING
BAKELITE OR
ACRYL RESIN PLATE
D
d
S
T
t
figure 9
2πD
Cd
1
f0
T(t+0.75d)
The adhesive agent used between the element and the
support ring should be elastic, such as silicon rubber.
相关PDF资料 |
PDF描述 |
|---|---|
| KBS-27DB-3T | BUZZER PIEZO 3.0KHZ 30V PCB |
| KBS-47DA-06C-8 | BUZZR PIEZO ELEMENT 0.6KHZ 41MM |
| LABELDISPNSR | LABEL DISPENSER |
| LOTION 8OZ | HAND LOTION ESD DISSIPATIVE |
| LPCGC151M | GROUND CORD LO-PRO 15' W/RESIS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KBS-27DA-3A | 功能描述:音频指示器及警报器 AUDIO BUZZERS RoHS:否 制造商:PUI Audio 产品:Indicators 声压级:85 dB 音调:Continuous 频率:2300 Hz +/- 300 Hz 电压额定值:5 VDC 电流额定值:30 mA 端接类型: 直径:12 mm 安装:Through Hole |
| KBS-27DA-5A | 功能描述:音频指示器及警报器 AUDIO BUZZERS RoHS:否 制造商:PUI Audio 产品:Indicators 声压级:85 dB 音调:Continuous 频率:2300 Hz +/- 300 Hz 电压额定值:5 VDC 电流额定值:30 mA 端接类型: 直径:12 mm 安装:Through Hole |
| KBS-27DA-5C-105 | 功能描述:音频指示器及警报器 4.6KHz 30V RoHS:否 制造商:PUI Audio 产品:Indicators 声压级:85 dB 音调:Continuous 频率:2300 Hz +/- 300 Hz 电压额定值:5 VDC 电流额定值:30 mA 端接类型: 直径:12 mm 安装:Through Hole |
| KBS-27DA-5C-108 | 功能描述:音频指示器及警报器 AUDIO BUZZERS RoHS:否 制造商:PUI Audio 产品:Indicators 声压级:85 dB 音调:Continuous 频率:2300 Hz +/- 300 Hz 电压额定值:5 VDC 电流额定值:30 mA 端接类型: 直径:12 mm 安装:Through Hole |
| KBS-27DA-5C-56 | 功能描述:音频指示器及警报器 AUDIO BUZZERS RoHS:否 制造商:PUI Audio 产品:Indicators 声压级:85 dB 音调:Continuous 频率:2300 Hz +/- 300 Hz 电压额定值:5 VDC 电流额定值:30 mA 端接类型: 直径:12 mm 安装:Through Hole |
发布紧急采购，3分钟左右您将得到回复。