参数资料
| 型号： | KIT33912EVME |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 20/50页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION FOR MC33912 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
FreeMASTER Control Page
Figure 3-2. Control/Status Array
3.5
Pulse Width Modulation
The Pulse Width Modulation serves to directly control the High Side and the Low Side Switch Drivers. The operating pulses have
an adjustable frequency from 1Hz to 1MHz. In the highest frequencies adjustment isn’t precise. A frequency change is possible
by dragging the blue frequency bar, with the range of the bar selectable by a drop down menu. Each following range has a scale
one order higher. Width of the duty cycle is adjustable by percentage via the blue duty blue bar, with a minimum step five percent
adjustment. For a zero percentage the Pulse Width Modulation terminal is permanently low, and for a hundred percent the
terminal is high. See Figure 3-3 .
Figure 3-3. Pulse Width Modulation Control Panel
3.6
Watchdog Service
In the SBCLIN device a watchdog pin is included, which is a configuration terminal for the internal watchdog. When the pin is
directly connected to the ground (place JP1, JP2), this terminal disables the watchdog function. When this terminal is left open
(move JP2), the watchdog period is fixed to its default value of 150ms. If the on-board resistor is connected (place JP2, move
JP1) to this terminal, then it configures the watchdog period to 16ms.
If the on-board watchdog resistor is connected and the GUI is started or a reset condition passes watchdog servicing is activated
automatically; see Figure 3-4 .
The user can extend the watchdog clear process by selecting the WDx bits in the Timing Control Register, then the button labelled
16 ms redisplays with the relevant clearing time. This configuration is valid only if the windowing watchdog is active.
The user can stop the watchdog servicing by clicking the button labelled 16 ms , which means the watchdog counter is not
properly cleared while it’s window is open for clears, and the MC33912 device will reset the microcontroller. The same sequence
of events will occur, if the user disables the watchdog service by clicking the button labelled WD ON .
When there is a direct connection of the watchdog terminal to the ground, the watchdog service is disabled automatically.
12
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| KIT33932VWEVBE | KIT EVALUATION FOR MC33932 |
| KIT33982CEVBE | KIT EVAL 33982 HIGH SIDE SWITCH |
| KIT33984CEVBE | KIT EVAL 33984 HIGH SIDE SWITCH |
| KIT33988CEVBE | KIT EVAL 33988 HIGH SIDE SWITCH |
| KIT33996EKEVB | KIT EVAL 33996 16OUTPUT SW W/SPI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KIT33912G5DGEVME | 功能描述:电源管理IC开发工具 33912G5 LIN SBC KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33926PNBEVBE | 功能描述:电源管理IC开发工具 5.2 A H-BRIDGE W/LOAD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33927EKEVBE | 功能描述:电源管理IC开发工具 THREE-PHASE FET PRE-DRIV RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| KIT33932EKEVBE | 功能描述:界面开发工具 5.0 A THROTTLE CONROL H RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| KIT33932VWEVBE | 功能描述:电源管理IC开发工具 5.0A THROTTLE CONTROL H RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。