- 您现在的位置：买卖IC网 > PDF目录17116 > KITMPR083EVM (Freescale Semiconductor)KIT EVAL 8POSITION ROTARY TOUCH PDF资料下载
参数资料
| 型号： | KITMPR083EVM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 5/35页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL 8POSITION ROTARY TOUCH |
| 标准包装： | 1 |
| 传感器类型： | 触摸，电容式 |
| 传感范围： | 8 个按钮/键 |
| 接口： | I²C |
| 电源电压： | 1.8 V ~ 3.6 V |
| 嵌入式： | 是，其它 |
| 已供物品： | 板，缆线，CD |
| 已用 IC / 零件： | MPR083 |
| 相关产品： | MPR083EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR083QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR083Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR083EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR083EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
MPR083
Sensors
Freescale Semiconductor
13
4.3
Run1 Mode
When in Run1 mode the sensor controller will run continuously. During Run1 all the modules are synchronized by the Master Tick
Period. This value can be set by using the Master Tick Period Register as outlined in the following section.
While in this mode all functionality of the MPR083 is enabled; touch detection will occur, and I2C communication will be available.
This mode is enabled by setting the Configuration Register’s RUNE and DCE bits high.
4.3.1
Master Tick Period Register
The Master Tick Period Register is used to set the master tick of this system. All parts of the system are synchronized to this
counter. This register is overridden in all modes except for Run1. When not in Run1 mode, the value of this register is ignored
and 8ms is used for the primary clock. The I2C slave address of the Master Tick Period Register is 0x05.
Figure 16. Master Tick Period Register
4.4
Run2 Mode
When in Run2 mode the sensor controller will continue to scan the electrodes but a low power state will be enabled between
each cycle. Because of this, any I2C communication that occurs, may or may not respond while the sensor is in this mode.
If DCE is enabled the sensor controller transitions between low power and active states. During the active part of the cycle
communication with the sensor controller is possible; however, Freescale always requires users to issue an ATTN signal prior to
initiating communications. Accessing the I2C interface while DCE mode is enabled without sending an ATTN signal first is likely
to produce invalid data.
This mode is enabled by setting the Configuration Register’s RUNE bit high and DCE bit low. The only way to exit this mode is
to toggle the Attention Pin, refer to Section 4.7.
4.5
Stop1 Mode
When in Stop1 mode the sensor controller will not scan the electrodes. While capacitance sensing is disabled I2C
communications will still be accepted and the sensor controller will maintain instantaneous response to all register requests. This
is the only mode in which register values can be set.
This mode is enabled by setting the Configuration Register’s RUNE bit low and DCE bit high.
4.6
Stop2 Mode
When in Stop2 mode the sensor controller will not scan the electrodes or accept I2C communication. The MPR083 is off during
this mode.
This mode is enabled by setting the Configuration Register’s RUNE bit low and DCE bit low. The only way to exit this mode is to
toggle the Attention Pin, refer to Section 4.7.
7
6
543210
R
MTP
W
Reset:
0
000101
= Unimplemented
Table 9. Master Tick Period Register Field Descriptions
Field
Description
7:0
MTP
Master Tick Period – The Master Tick Period selects or reports the current value of the
touch sensor controller’s primary clock multiplier. The resulting period must be in the
range 5ms to 31ms. If the value is outside of this range the MTP will be set to 00011010.
00000000 Encoding 0 – Sets the primary clock multiplier to 5
~
00011010 Encoding 26 - Sets the primary clock multiplier to 31
相关PDF资料 |
PDF描述 |
|---|---|
| RCC12DREN-S734 | CONN EDGECARD 24POS .100 EYELET |
| VE-J7P-EZ | CONVERTER MOD DC/DC 13.8V 25W |
| GBM28DSEN | CONN EDGECARD 56POS .156 EYELET |
| ADR06WARZ-RL | IC VREF SERIES PREC 3V 8SOIC |
| RCC12DREH-S734 | CONN EDGECARD 24POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KITMPR084EVM | 功能描述:光学传感器开发工具 8 TOUCH PADS RoHS:否 制造商:ams 工具用于评估: 接口类型: 最大工作温度: |
| KITMPR121EVM | 功能描述:触摸传感器开发工具 MPR121 Sensor Tool Box RoHS:否 制造商:Cypress Semiconductor 工具用于评估: 接口类型: 工作电压: 最大工作温度: |
| KITMPR121EVM | 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit |
| KITMPVZ5004EVK | 功能描述:压力传感器开发工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXA6115AEVB | 功能描述:压力传感器开发工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。