- 您现在的位置：买卖IC网 > PDF目录3998 > KMPC8241LZQ266D (Freescale Semiconductor)IC MPU 32BIT 266MHZ 357-PBGA PDF资料下载
参数资料
| 型号： | KMPC8241LZQ266D |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 39/58页 |
| 文件大小： | 0K |
| 描述： | IC MPU 32BIT 266MHZ 357-PBGA |
| 标准包装： | 2 |
| 系列： | MPC82xx |
| 处理器类型： | 32-位 MPC82xx PowerQUICC II |
| 速度： | 266MHz |
| 电压： | 1.8V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 357-BBGA |
| 供应商设备封装： | 357-PBGA（25x25） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
MPC8241 Integrated Processor Hardware Specifications, Rev. 10
44
Freescale Semiconductor
System Design Information
7.4
Pull-Up/Pull-Down Resistor Requirements
The data bus input receivers are normally turned off when no read operation is in progress; therefore, they
do not require pull-up resistors on the bus. The data bus signals are: MDH[0:31], MDL[0:31], and
PAR[0:7].
If the 32-bit data bus mode is selected, the input receivers of the unused data and parity bits (MDL[0:31]
and PAR[4:7]) are disabled, and their outputs drive logic zeros when they would otherwise be driven. For
this mode, these pins do not require pull-up resistors and should be left unconnected to minimize possible
output switching.
The TEST0 pin requires a pull-up resistor of 120
Ω or less connected to GVDD_OVDD.
RTC should have weak pull-up resistors (2–10 k
Ω) connected to GV
DD_OVDD and that the following
signals should be pulled up to GVDD_OVDD with weak pull-up resistors (2–10 kΩ): SDA, SCL, SMI,
SRESET/SDMA12, TBEN/SDMA13, CHKSTOP_IN/SDMA14, TRIG_IN/RCS2, QACK/DA0, and
DRDY.
The following PCI control signals should be pulled up to LVDD (the clamping voltage) with weak pull-up
resistors (2–10 k
Ω): DEVSEL, FRAME, IRDY, LOCK, PERR, SERR, STOP, and TRDY. The resistor
values may need to have stronger adjustment to reduce induced noise on specific board designs.
The following pins have internal pull-up resistors enabled at all times: REQ[3:0], REQ4/DA4, TCK, TDI,
TMS, and TRST. See Table 16.
The following pins have internal pull-up resistors that are enabled only while the device is in the reset state:
GNT4/DA5, MDL0, FOE, RCS0, SDRAS, SDCAS, CKE, AS, MCP, MAA[0:2], and PMAA[0:2]. See
The following pins are reset configuration pins: GNT4/DA5, MDL[0], FOE, RCS0, CKE, AS, MCP,
QACK/DA0, MAA[0:2], PMAA[0:2], SDMA[1:0], MDH[16:31], and PLL_CFG[0:4]/DA[10:15]. These
pins are sampled during reset to configure the device. The PLL_CFG[0:4] signals are sampled a few clocks
after the negation of HRST_CPU and HRST_CTRL.
Reset configuration pins should be tied to GND by means of 1-k
Ω pull-down resistors to ensure that a logic
zero level is read into the configuration bits during reset if the default logic-one level is not desired.
Any other unused active low input pins should be tied to a logic-one level by means of weak pull-up
resistors (2–10 k
Ω) to the appropriate power supply listed in Table 16. Unused active high input pins
should be tied to GND by means of weak pull-down resistors (2–10 k
Ω).
7.5
PCI Reference Voltage—LVDD
The MPC8241 PCI reference voltage (LVDD) pins should be connected to 3.3 ± 0.3 V power supply if
interfacing the MPC8241 into a 3.3-V PCI bus system. Similarly, the LVDD pins should be connected to
5.0 V ± 5% power supply if interfacing the MPC8241 into a 5-V PCI bus system. For either reference
voltage, the MPC8241 always performs 3.3-V signaling as described in the PCI Local Bus Specification
(Rev. 2.2). The MPC8241 tolerates 5-V signals when interfaced into a 5-V PCI bus system. (See Errata
No. 18 in the MPC8245/MPC8241 Integrated Processor Chip Errata).
相关PDF资料 |
PDF描述 |
|---|---|
| KMPC8241LZQ200D | IC MPU 32BIT 200MHZ 357-PBGA |
| KMPC8241LZQ166D | IC MPU 32BIT 166MHZ 357-PBGA |
| KMPC8241LVR266D | IC MPU 32BIT 266MHZ 357-PBGA |
| IDT7054L35PRF | IC SRAM 32KBIT 35NS 128TQFP |
| IDT7142SA55C | IC SRAM 16KBIT 55NS 48DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KMPC8241TVR166D | 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| KMPC8241TVR200D | 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| KMPC8241TZQ166D | 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| KMPC8241TZQ200D | 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| KMPC8245ARVV400D | 功能描述:微处理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
发布紧急采购，3分钟左右您将得到回复。