参数资料
| 型号： | KS8999 |
| 厂商： | Micrel Inc |
| 文件页数： | 19/52页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 10/100 9PORT 208PQFP |
| 标准包装： | 24 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 208-MQFP，208-PQFP |
| 供应商设备封装： | 208-PQFP（28x28） |
| 包装： | 散装 |
| 配用： | 576-1023-ND - BOARD EVAL EXPERIMENT FOR KS8999 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
KS8999
Micrel
KS8999
26
January 2005
SNI Interface (7-wire) Operation
The SNI (Serial Network Interface) is compatible with some controllers used for network layer protocol processing. KS8999
acts like a PHY device to external controllers. This interface can be directly connected to these types of devices. The signals
are divided into two groups, one being for transmission and the other being the receive side. The signals involved are described
in the table below.
KS8999
SNI Signal
Description
SNI Signal
Input/Output
TXEN
Transmit enable
MTXEN
Input
TXD
Serial transmit data
MTXD[0]
Input
TXC
Transmit clock
MTXC
Output
COL
Collision detection
MCOL
Output
CRS
Carrier sense
MRXDV
Output
RXD
Serial receive data
MRXD[0]
Output
RXC
Receive clock
MRXC
Output
Table 2. SNI Signals
This interface is a bit wide data interface and therefore runs at the network bit rate (not encoded). An additional signal on the
transmit side indicates when data is valid. Likewise, the receive side has an indicator that conveys when the data is valid.
For half-duplex operation there is a signal that indicate a collision has occurred during transmission.
Programmable Features
Priority Schemes
The KS8999 can determine priority through three different means at the ingress point. The first method is a simple per port
method, the second is via the 802.1p frame tag and the third is by viewing the DSCP (TOS) field in the IPv4 header. Of course
for the priority to be effective, the high and low priority queues must be enabled on the destination port or egress point.
Per Port Method
General priority can be specified on a per port basis. In this type of priority all traffic from the specified input port is considered
high priority in the destination queue. This can be useful in IP phone applications mixed with other data types of traffic where
the IP phone connects to a specific port. The IP phone traffic would be high priority (outbound) to the wide area network. The
inbound traffic to the IP phone is all of the same priority to the IP phone.
802.1p Method
This method works well when used with ports that have mixed data and media flows. The inbound port examines the priority
field in the tag and determines the high or low priority. Priority profiles are setup in the Priority Classification Control in the
EEPROM.
IPv4 DSCP Method
This is another per frame way of determining outbound priority. The DSCP (Differentiated Services Code Point – RFC#2474)
method uses the TOS field in the IP header to determine high and low priority on a per code point basis. Each fully decoded
code point can have either a high or low priority. A larger spectrum of priority flows can be defined with this larger code space.
More specific to implementation, the most significant 6 bits of the TOS field are fully decoded into 64 possibilities, and the
singular code that results is compared against the corresponding bit in the DSCP register. If the register bit is a 1, the priority
is high and if 0, the priority is low.
Other Priority Considerations
When setting up the priority scheme, one should consider other available controls to regulate the traffic. One of these is Priority
Control Scheme (register 2 bits 2-3) which controls the interleaving of high and low priority frames. Options allow from a 2:1
ratio up to a setting that sends all the high priority first. This setting controls all ports globally. Another global feature is Priority
Buffer Reserve (register 2 bit 1). If this is set, there is a 6KB (10%) buffer dedicated to high priority traffic, otherwise if cleared
the buffer is shared between all traffic.
On an individual port basis there are controls that enable DSCP, 802.1p, port based and high/low priority queues. These are
contained in registers 4-12 bits 5-3 and 0. It should be noted that there is a special pin that generally enables the 802.1p priority
for all ports (pin 91). When this pin is active (high) all ports will have the 802.1p priority enabled unless specifically disabled
by EEPROM programming (bit 4 of registers 4-12). Default high priority is a value greater than 4 in the VLAN tag with low priority
being 3 or less.
相关PDF资料 |
PDF描述 |
|---|---|
| LFXP20E-3FN388I | IC FPGA 19.7KLUTS 268I/O 388-BGA |
| LFXP20C-4FN388C | IC FPGA 19.7KLUTS 268I/O 388-BGA |
| LFXP15E-5F484C | IC FPGA 15.4KLUTS 300I/O 484-BGA |
| LFXP15E-4F484I | IC FPGA 15.4KLUTS 300I/O 484-BGA |
| LFXP15C-5F484C | IC FPGA 15.4KLUTS 300I/O 484-BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KS8999_11 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Integrated 9-Port 10/100 Switch with PHY and Frame Buffer |
| KS8999-EVAL | 功能描述:BOARD EVAL EXPERIMENT FOR KS8999 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| KS8999I | 功能描述:IC SWITCH 9-PORT 10/100 208-PQFP RoHS:否 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| KS9/KSE9/59/103/115 | 制造商:PEPPERL+FUCHS 功能描述:Through beam cable sensor,PNP o/p 250mm |
| KS9~11 | 制造商:Tohodenzai 功能描述: |
发布紧急采购，3分钟左右您将得到回复。