参数资料
| 型号： | KSZ8021RNL |
| 厂商： | Micrel Inc |
| 文件页数： | 11/43页 |
| 文件大小： | 0K |
| 描述： | TXRX PHY 100BASE TX 3.3V 24QFN |
| 标准包装： | 75 |
| 类型： | PHY 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RMII |
| 电源电压： | 1.8V，2.5V，3.3V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 管件 |
| 其它名称： | 576-3740-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
Micrel, Inc.
KSZ8021RNL / KSZ8031RNL
August 2010
19
M9999-082710-1.0
MII Management (MIIM) Interface
The KSZ8021/31RNL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input /
Output (MDIO) Interface. This interface enables upper-layer device, like a MAC processor, to monitor and control the state
of the KSZ8021/31RNL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY
settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the clock line (MDC) and the data line (MDIO).
A specific protocol that operates across the aforementioned physical connection that allows the external controller
to communicate with one or more PHY devices.
A set of 16-bit MDIO registers. Registers [0:8] are standard registers, and their functions are defined per the IEEE
802.3 Specification. The additional registers are provided for expanded functionality. See “Register Map” section
for details.
The KSZ8021/31RNL supports only two unique PHY addresses, 0x0h and 0x3h. The PHYAD[1:0] strapping pin is used to
select either 0x0h or 0x3h as the unique PHY address for the KSZ8021/31RNL device.
Table 3 shows the MII Management frame format for the KSZ8021/31RNL.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
000AA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
000AA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 3. MII Management Frame Format – for KSZ8021/31RNL
Interrupt (INTRP)
The INTRP (pin 18) is an optional interrupt signal that is used to inform the external controller that there has been a status
update to the KSZ8021/31RNL PHY register. Register 1Bh, bits [15:8] are the interrupt control bits to enable and disable
the conditions for asserting the INTRP signal. Register 1Bh, bits [7:0] are the interrupt status bits to indicate which
interrupt conditions have occurred. The interrupt status bits are cleared after reading register 1Bh.
Register 1Fh, bit 9 sets the interrupt level to active high or active low. The default is active low.
The MII management bus option gives the MAC processor complete access to the KSZ8021/31RNL control and status
registers. Additionally, an interrupt pin eliminates the need for the processor to poll the PHY for status change.
HP Auto MDI/MDI-X
The HP Auto MDI/MDI-X configuration eliminates the confusion of whether to use a straight cable or a crossover cable
between the KSZ8021/31RNL and its link partner. This feature allows the KSZ8021/31RNL to use either type of cable to
connect with a link partner that is in either MDI or MDI-X mode. The auto-sense function detects transmit and receive
pairs from the link partner, and then assigns transmit and receive pairs of the KSZ8021/31RNL accordingly.
HP Auto MDI/MDI-X is enabled by default. It is disabled by writing a one to register 1Fh, bit [13]. MDI and MDI-X mode is
selected by register 1Fh, bit [14] if HP Auto MDI/MDI-X is disabled.
An isolation transformer with symmetrical transmit and receive data paths is recommended to support auto MDI/MDI-X.
The IEEE 802.3 Standard defines MDI and MDI-X in Table 4.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B41-MW-F2 | CONVERTER MOD DC/DC 12V 100W |
| MS3126E20-41SX | CONN PLUG 41POS STRAIGHT W/SCKT |
| VE-B2Y-MV-F3 | CONVERTER MOD DC/DC 3.3V 99W |
| MS27474T10B98SB | CONN RCPT 6POS JAM NUT W/SCKT |
| VE-B1Z-MV-F2 | CONVERTER MOD DC/DC 2V 60W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8021RNL TR | 功能描述:以太网 IC 3.3V, 100Base-FX Physical Layer Transceiver with RMII support (24-QFN) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8021RNL-EVAL | 功能描述:以太网开发工具 3.3V, 100Base-FX Physical Layer Transceiver w/ RMII Support - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8021RNL-TR | 功能描述:1/1 Transceiver Full RMII 24-QFN (4x4) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:过期 类型:收发器 协议:RMII 驱动器/接收器数:1/1 双工:全 接收器滞后:- 数据速率:- 电压 - 电源:1.8V，2.5V，3.3V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商器件封装:24-QFN（4x4） 标准包装:1 |
| KSZ8031RNL | 功能描述:TXRX PHY 100BASE TX 3.3V 24QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND |
| KSZ8031RNL TR | 功能描述:以太网 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver w/ RMII Support (24-QFN) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。