参数资料
型号: KSZ8041TL
厂商: Micrel Inc
文件页数: 10/58页
文件大小: 0K
描述: TRANSCEIVER 10/100BASE 48-TQFP
标准包装: 250
类型: 收发器
驱动器/接收器数: 1/1
规程: MII,RMII
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 48-TQFP
供应商设备封装: 48-TQFP(7x7)
包装: 托盘
产品目录页面: 1080 (CN2011-ZH PDF)
配用: 576-3295-ND - BOARD EVALUATION KSZ8041TL
其它名称: 576-1619
Micrel, Inc.
KSZ8041TL/FTL
April 2007
18
M9999-042707-1.1
10Base-T Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and
a PLL performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data.
A squelch circuit rejects signals with levels less than 400 mV or with short pulse widths to prevent noise at the RX+ and
RX- inputs from falsely trigger the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming
signal and the KSZ8041TL/FTL decodes a data frame. The receive clock is kept active during idle periods in between
data reception.
SQE and Jabber Function (10Base-T only)
In 10Base-T operation, a short pulse is put out on the COL pin after each frame is transmitted. This SQE Test is required
as a test of the 10Base-T transmit/receive path. If transmit enable (TXEN) is high for more than 20 ms (jabbering), the
10Base-T transmitter is disabled and COL is asserted high. If TXEN is then driven low for more than 250 ms, the 10Base-
T transmitter is re-enabled and COL is de-asserted (returns to low).
Auto-Negotiation
The KSZ8041TL/FTL conforms to the auto-negotiation protocol, defined in Clause 28 of the IEEE 802.3u specification.
Auto-negotiation is enabled by either hardware pin strapping (pin 30) or software (register 0h bit 12).
Auto-negotiation allows unshielded twisted pair (UTP) link partners to select the highest common mode of operation. Link
partners advertise their capabilities to each other, and then compare their own capabilities with those they received from
their link partners. The highest speed and duplex setting that is common to the two link partners is selected as the mode
of operation.
The following list shows the speed and duplex operation mode from highest to lowest.
Priority 1: 100Base-TX, full-duplex
Priority 2: 100Base-TX, half-duplex
Priority 3: 10Base-T, full-duplex
Priority 4: 10Base-T, half-duplex
If auto-negotiation is not supported or the KSZ8041TL/FTL link partner is forced to bypass auto-negotiation, the
KSZ8041TL/FTL sets its operating mode by observing the signal at its receiver. This is known as parallel detection, and
allows the KSZ8041TL/FTL to establish link by listening for a fixed signal protocol in the absence of auto-negotiation
advertisement protocol.
The auto-negotiation link up process is shown in the following flow chart.
相关PDF资料
PDF描述
LTC2804CGN-1#PBF IC TXRX RS232 DUAL 16-SSOP
AD421BRRL IC DAC SNGL 16BIT 16-SOIC T/R
DAC8800FP IC DAC 8BIT OCTAL CMOS 20-DIP
AD5320BRM-REEL7 IC DAC 12BIT R-R W/BUFF 8-MSOP
AD5320BRM-REEL IC DAC 12BIT R-R W/BUFF 8-MSOP
相关代理商/技术参数
参数描述
KSZ8041TL A3 制造商:Micrel Inc 功能描述:PHY 1-CH 10Mbps/100Mbps 48-Pin TQFP T/R
KSZ8041TL A3 TR 制造商:Micrel Inc 功能描述:PHY 1-CH 10Mbps/100Mbps 48-Pin TQFP T/R
KSZ8041TL TR 功能描述:以太网 IC Physical Layer Transceiver 10/100BASE-T/TX (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ8041TLA3 功能描述:TRANSCEIVER 10/100 48-TQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC(0.154",3.90mm 宽) 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND
KSZ8041TLA3TR 功能描述:TRANSCEIVER 10/100 48-TQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC(0.154",3.90mm 宽) 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND