参数资料
| 型号： | KSZ8993M |
| 厂商： | Micrel Inc |
| 文件页数： | 13/85页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 10/100 3PORT 128PQFP |
| 标准包装： | 66 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-PQFP（14x20） |
| 包装： | 托盘 |
| 产品目录页面： | 1081 (CN2011-ZH PDF) |
| 其它名称： | 576-1037 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页
Micrel, Inc.
KS8993M/ML/MI
April 2005
20
M9999-041205
Functional Description
The KS8993M contains two 10/100 physical layer transceivers and three MAC units with an integrated Layer 2
managed switch.
The KS8993M has the flexibility to reside in either a managed or unmanaged design. In a managed design, the
host processor has complete control of the KS8993M via the SMI interface, MIIM interface, SPI bus, or I
2C bus.
An unmanaged design is achieved through I/O strapping and/or EEPROM programming at system reset time.
On the media side, the KS8993M supports IEEE 802.3 10BASE-T and 100BASE-TX on both PHY ports, and
100BASE-FX on PHY port 1. The KS8993M can be used as a media converter.
The KS8993ML is the single supply version with all the identical rich features of the KS8993M. In the KS8993ML
version, pin number 22 provides 1.8V output power to the KS8993ML’s VDDC, VDDA, and VDDAP power pins. Refer
to the Pin Description table for information about pin 22 (Pin Description and I/0 Assignment).
Physical signal transmission and reception are enhanced through the use of patented analog circuitries that make
the design more efficient and allow for lower power consumption and smaller chip die size.
Functional Overview: Physical Layer Transceiver
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel to serial conversion, 4B/5B coding, scrambling, NRZ to
NRZI conversion, MLT3 encoding and transmission. The circuit starts with a parallel-to-serial conversion, which
converts the MII data from the MAC into a 125MHz serial bit stream. The data and control stream is then
converted into 4B/5B coding and followed by a scrambler. The serialized data is further converted from NRZ to
NRZI format, and then transmitted in MLT3 current output. The output current is set by an external 1% 3.01 K
resistor for the 1:1 transformer ratio. It has a typical rise/fall time of 4ns and complies with the ANSI TP-PMD
standard regarding amplitude balance, overshoot, and timing jitter. The wave-shaped 10BASE-T output is also
incorporated into the 100BASE-TX transmitter.
100BASE-TX Receive
The 100BASE-TX receiver function performs adaptive equalization, DC restoration, MLT3 to NRZI conversion,
data and clock recovery, NRZI to NRZ conversion, de-scrambling, 4B/5B decoding and serial-to-parallel
conversion. The receiving side starts with the equalization filter to compensate for inter-symbol interference (ISI)
over the twisted pair cable. Since the amplitude loss and phase distortion is a function of the length of the cable,
the equalizer has to adjust its characteristics to optimize the performance. In this design, the variable equalizer
will make an initial estimation based on comparisons of incoming signal strength against some known cable
characteristics, then it tunes itself for optimization. This is an ongoing process and can self adjust against
environmental changes such as temperature variations.
The equalized signal then goes through a DC restoration and data conversion block. The DC restoration circuit is
used to compensate for the effect of base line wander and improve the dynamic range. The differential data
conversion circuit converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is
then used to convert the NRZI signal into the NRZ format. The signal is then sent through the de-scrambler
followed by the 4B/5B decoder. Finally, the NRZ serial data is converted to the MII format and provided as the
input data to the MAC.
相关PDF资料 |
PDF描述 |
|---|---|
| KSZ8995M | IC SWITCH 10/100 5PORT 128PQFP |
| RSM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
| LFEC6E-3QN208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| LFEC6E-3Q208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| RMM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8993MA5 | 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| KSZ8993M-EVAL | 功能描述:以太网开发工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8993MI | 功能描述:以太网 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8993ML | 功能描述:以太网 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8993ML-EVAL | 功能描述:以太网开发工具 KSZ8993ML Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。