- 您现在的位置：买卖IC网 > PDF目录43898 > L296PHT (STMICROELECTRONICS) 7 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PZFM15 PDF资料下载
参数资料
| 型号： | L296PHT |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 7 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PZFM15 |
| 封装： | PLASTIC, POWER PACK-15 |
| 文件页数： | 12/22页 |
| 文件大小： | 285K |
| 代理商： | L296PHT |
PIN FUNCTIONS
N
°
Name
Function
1
CROWBAR INPUT
Voltage Sense Input for Crowbar Overvoltage Protection. Normally connected to the
feedback input thus triggering the SCR when V out exceeds nominal by 20 %. May
also monitor the input and a voltage divider can be added to increase the threshold.
Connected to ground when SCR not used.
2
OUTPUT
Regulator Output
3
SUPPLY VOLTAGE
Unrergulated Voltage Input. An internal Regulator Powers the L296s Internal Logic.
4
CURRENT LIMIT
A resistor connected between this terminal and ground sets the current limiter
threshold. If this terminal is left unconnected the threshold is internally set (see
electrical characteristics).
5
SOFT START
Soft Start Time Constant. A capacitor is connected between this terminal and ground
to define the soft start time constant. This capacitor also determines the average
short circuit output current.
6
INHIBIT INPUT
TTL – Level Remote Inhibit. A logic high level on this input disables the device.
7
SYNC INPUT
Multiple L296s are synchronized by connecting the pin 7 inputs together and omitting
the oscillator RC network on all but one device.
8
GROUND
Common Ground Terminal
9
FREQUENCY
COMPENSATION
A series RC network connected between this terminal and ground determines the
regulation loop gain characteristics.
10
FEEDBACK INPUT
The Feedback Terminal on the Regulation Loop. The output is connected directly to
this terminal for 5.1V operation ; it is connected via a divider for higher voltages.
11
OSCILLATOR
A parallel RC networki connected to this terminal determines the switching frequency.
This pin must be connected to pin 7 input when the internal oscillator is used.
12
RESET INPUT
Input of the Reset Circuit. The threshold is roughly 5 V. It may be connected to the
feedback point or via a divider to the input.
13
RESET DELAY
A capacitor connected between this terminal and ground determines the reset signal
delay time.
14
RESET OUTPUT
Open collector reset signal output. This output is high when the supply is safe.
15
CROWBAR OUTPUT
SCR gate drive output of the crowbar circuit.
BLOCK DIAGRAM
L296 - L296P
2/22
相关PDF资料 |
PDF描述 |
|---|---|
| L296P | 7 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PZFM15 |
| L297/1 | STEPPER MOTOR CONTROLLER, PDIP20 |
| L297D013TR | STEPPER MOTOR CONTROLLER, PDSO20 |
| L3G462ATR | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| L482 | SPECIALTY ANALOG CIRCUIT, PDIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L297 | 制造商:Panasonic Industrial Company 功能描述:INTEGRATED CIRC |
| L297/1 | 功能描述:马达/运动/点火控制器和驱动器 Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L297/1 | 制造商:STMicroelectronics 功能描述:IC STEPPER MOTOR CONTROLLER |
| L2971 | 制造商:STMicroelectronics 功能描述:Stepper motor controller,L297/1 DIP20 |
| L297A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Stepper Motor Controller/Driver |
发布紧急采购，3分钟左右您将得到回复。