参数资料
型号: L484D1013TR
厂商: STMICROELECTRONICS
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PDSO16
封装: SOP-16
文件页数: 7/11页
文件大小: 454K
代理商: L484D1013TR
Obsolete
Product(s)
- Obsolete
Product(s)
DUMP PROTECTION
Symbol
Paramater
Test Conditions
Min.
Typ.
Max.
Unit
VDZ
Zener Dump (pin 12)
Ipin12 = 2mA
7.5
9.5
V
(*) Note 1 : TD/T is given by the formula :
TD
1
=
T
1 + I7D/I7C
(**) Note 2 :
TD
K
=
T
1 + I7D/I7C
K value depends on the pick–up used in the application ; typically K = 0.1
(***) Note 3 : the permanent conduction protection is guaranteed over the full temperature range
CIRCUIT OPERATION
The L484 controls the charging angle (dwell) and
the peak value of the primary current in the coil over
the full range of operating conditions.
The coil current is limited to a predetermined level
by means of a negative feedback circuit including a
current sensing resistor, a comparator, the driver
stage and the power switch.
The dwell control circuit keeps the output stage in its
active region during current limitation. The time the
output stage is operating in the active region (de-
saturation time), is sufficient to compensate for
possible variation in the energy stored due to the ac-
celeration of the motor ; moreover this time is limited
to avoid excessive power dissipation.
MAGNETIC PICK–UP CHARACTERISTICS
The typical magnetic pickup waveforms are shown
in fig. 1, the amplitude of the signal being a function
of the frequency. However on the market there are
many types of magnetic pickup, of which the wave-
forms may differ very much. Adjusting the value of
the resistor R11 on pin 2 and/or adding a resistor Ra
between the pin 6 (dwell adjust) and pin 11, as
shown in the application circuit, it is possible to adapt
the L484 to a wide range of magnetic pickup wave-
forms.
Particularly by means of the resistor R11 on pin 2 it
is possible to define the maximum advance of the
conduction start into the coil . This is very useful at
high pick–up frequency.
CONTROL OF THE DWELL ANGLE
The dwell angle control circuit defines the conduc-
tion time of the output darlington, versus the speed
of rotation, the supply voltage and the charac-
teristics of the coil.
In each cycle the time the transistor operates in the
active region is compared with a reference time and
the error signal amplified to advance or delay the
conduction in the next cycle. To limit the power dissi-
pation the
desaturation
time is typically fixed
to 10% of the period T.
At very low frequencies the ON thershold is fixed at
200mV of the input signal and the desaturation time
is mainly determined by the peak waveform. This
positive threshold also prevents permanent conduc-
tion when the motor is stopped. When the input fre-
quency increases the dwell control gradually sets
the desaturation time to 10% of the period. At higher
frequencies the ON threshold becomes negative to
permit a conduction angle of more than 50% always
keeping desaturation time to 10% of the period.
CURRENT LIMITING
The current in the coil is measured by means of a
voltage drop across a suitable resistor in the emitter
lead of the power transistor. When the threshold
voltage (260mV typ) is reached, the coil current is
kept constant via a feedback loop.
L484
5/11
相关PDF资料
PDF描述
L4916 SPECIALTY ANALOG CIRCUIT, PDIP8
L6232E BRUSHLESS DC MOTOR CONTROLLER, 3.5 A, PQCC28
L6234 BRUSHLESS DC MOTOR CONTROLLER, 5 A, PDIP20
L6234PD BRUSHLESS DC MOTOR CONTROLLER, 5 A, PDSO20
L6235PD BRUSHLESS DC MOTOR CONTROLLER, 5.6 A, PDSO36
相关代理商/技术参数
参数描述
L485 制造商:LAUREL ELECTRONICS 功能描述:Modbus RS485, dual RJ11, communications plug-in board Laureate meters and counters. ;RoHS Compliant: Yes
L486 制造商:IXYS 制造商全称:IXYS Corporation 功能描述:IGBT Modules Sixpack, H Bridge
L4863 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:DUAL 2.2W AUDIO AMPLIFIER PLUS STEREO HEADPHONE FUNCTION
L4863_07 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:DUAL 2.2W AUDIO AMPLIFIER PLUS STEREO HEADPHONE FUNCTION
L4863-D16-T 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:DUAL 2.2W AUDIO AMPLIFIER PLUS STEREO HEADPHONE FUNCTION