- 您现在的位置：买卖IC网 > PDF目录79955 > L5991AD (STMICROELECTRONICS) 1.5 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | L5991AD |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 1.5 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | SO-16 |
| 文件页数： | 23/23页 |
| 文件大小： | 414K |
| 代理商： | L5991AD |
The oscillation frequency can be established with
the aid of the diagrams of fig. 14, where RT will be
intended as the parallel of RA and RB in normal
operation and RT = RA in standby, or considering
the following approximate relationships:
fosc
1
CT
(0.693 (RA // RB) + KT
(1),
which gives the normal operating frequency, and:
fSB
1
CT
(0.693 RA + KT
)
(2),
which gives the standby frequency, that is the one
the converter will operate at when lightly loaded.
In the above expressions, RA // RB means:
RA//RB
=
RA
RB
RA
+ RB
,
while KT is defined as:
KT
=
90 V15
= VREF
160 V15
= GND/OPEN
(3),
and is related to the duration of the falling-edge of
the sawtooth:
Td
≈ 30 109 + KT
CT (4).
Td is also the duration of the sync pulses deliv-
ered at pin 1 and defines the upper extreme of the
duty cycle range, Dx (see pin 15 for DX definition
and calculation) since the output is held low dur-
ing the falling edge.
In case V15 is connected to VREF, however, the
switching frequency will be a half the values taken
from fig. 14 or resulting from (1) and (2).
To prevent the oscillator frequency from switching
back and forth from fosc to fSB, the ratio fosc / fSB
must not exceed 5.5.
If during normal operation the IC is to be synchro-
nized to an external oscillator, RA, RB and CT
should be selected for a fosc lower than the master
frequency in any condition (typically, 10-20% ),
depending also on the tolerance of the parts.
Pin 3. DC (Duty Cycle Control). By biasing this
pin with a voltage between 1 and 3 V it is possible
to set the maximum duty cycle between 0 and the
upper extreme Dx (see pin 15).
If Dmax is the desired maximum duty cycle, the
voltage V3 to be applied to pin 3 is:
V3 = 5 - 2
(2-Dmax)
(5)
Dmax is determined by internal comparison be-
tween V3 and the oscillator ramp (see fig. 24),
thus in case the device is synchronized to an ex-
ternal frequency fext (and therefore the oscillator
amplitude is reduced), (5) changes into:
V3
= 5 4 exp
Dmax
RT
CT fext
(6)
A voltage below 1V will inhibit the driver output
stage. This could be used for a not-latched device
disable, for example in case of overvoltage pro-
tection (see application ideas).
If no limitation on the maximum duty cycle is re-
quired (i.e. DMAX = DX), the pin has to be left float-
ing. An internal pull-up (see fig. 24) holds the volt-
age above 3V. Should the pin pick up noise (e.g.
+
-
R2
R3
R1
CLAMP
D1
50
RA
CT
D
R
Q
600
A
D97IN729A
VREF
RCT
SYNC
CLK
2
4
1
16
ST-BY
RB
STANDBY
Figure 23. Oscillator and synchronization internal schematic.
L5991 - L5991A
9/23
相关PDF资料 |
PDF描述 |
|---|---|
| LM1301-9PV3AHF | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1501-7RV2AHF | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1501-9PV0A | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1501-9RV2HF | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM1601-7PV2F | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L5991AD13TR | 功能描述:电流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L5991D | 功能描述:电流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L5991D013TR | 功能描述:电流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L5993 | 功能描述:开关变换器、稳压器与控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| L5993D | 功能描述:开关变换器、稳压器与控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。