- 您现在的位置：买卖IC网 > PDF目录79701 > L6205D (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 5.6 A, PDSO20 PDF资料下载
参数资料
| 型号： | L6205D |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO20 |
| 封装： | SO-20 |
| 文件页数： | 16/21页 |
| 文件大小： | 395K |
| 代理商： | L6205D |
L6205
4/21
(6) Also connected at the output drain of the Overcurrent and Thermal protection MOSFET. Therefore, it has to be driven putting in series a
resistor with a value in the range of 2.2k
- 180K, recommended 100k
PIN DESCRIPTION
PACKAGE
Name
Type
Function
SO20/
PowerDIP20
PowerSO20
PIN #
1
6
IN1A
Logic Input
Bridge A Logic Input 1.
2
7
IN2A
Logic Input
Bridge A Logic Input 2.
3
8
SENSEA
Power Supply
Bridge A Source Pin. This pin must be connected to Power
Ground directly or through a sensing power resistor.
4
9
OUT1A
Power Output
Bridge A Output 1.
5, 6, 15, 16
1, 10, 11,
20
GND
Signal Ground terminals. In PowerDIP and SO packages,
these pins are also used for heat dissipation toward the
PCB.
7
12
OUT1B
Power Output
Bridge B Output 1.
8
13
SENSEB
Power Supply
Bridge B Source Pin. This pin must be connected to Power
Ground directly or through a sensing power resistor.
9
14
IN1B
Logic Input
Bridge B Logic Input 1.
10
15
IN2B
Logic Input
Bridge B Logic Input 2.
11
16
ENB
Logic Input (6)
Bridge B Enable. LOW logic level switches OFF all Power
MOSFETs of Bridge B. This pin is also connected to the
collector of the Overcurrent and Thermal Protection
transistor to implement over current protection.
If not used, it has to be connected to +5V through a
resistor.
12
17
VBOOT
Supply
Voltage
Bootstrap Voltage needed for driving the upper
PowerMOSFETs of both Bridge A and Bridge B.
13
18
OUT2B
Power Output
Bridge B Output 2.
14
19
VSB
Power Supply
Bridge B Power Supply Voltage. It must be connected to
the supply voltage together with pin VSA.
17
2
VSA
Power Supply
Bridge A Power Supply Voltage. It must be connected to
the supply voltage together with pin VSB.
18
3
OUT2A
Power Output
Bridge A Output 2.
19
4
VCP
Output
Charge Pump Oscillator Output.
20
5
ENA
Logic Input (6)
Bridge A Enable. LOW logic level switches OFF all Power
MOSFETs of Bridge A. This pin is also connected to the
collector of the Overcurrent and Thermal Protection
transistor to implement over current protection.
If not used, it has to be connected to +5V through a
resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| LM2595-3.3MWC | 2.6 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
| LS25-24 | 1-OUTPUT DC-DC UNREG PWR SUPPLY MODULE |
| LM4040CIZ-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PBCY3 |
| LTC1146CN | SPECIALTY ANALOG CIRCUIT, PDIP18 |
| LM1001-7EPD0 | 1-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6205D013TR | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6205N | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6205N | 制造商:STMicroelectronics 功能描述:IC FULL BRIDGE DRIVER |
| L6205N | 制造商:STMicroelectronics 功能描述:IC - Full Bridge Driver |
| L6205PD | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。