- 您现在的位置：买卖IC网 > PDF目录69003 > L6208D (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 PDF资料下载
参数资料
| 型号： | L6208D |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 |
| 封装： | SO-24 |
| 文件页数： | 9/27页 |
| 文件大小： | 462K |
| 代理商： | L6208D |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
17/27
L6208
Figure 20 shows the Overcurrent Detection operation. The Disable Time tDISABLE before recovering normal oper-
ation can be easily programmed by means of the accurate thresholds of the logic inputs. It is affected whether by
CEN and REN values and its magnitude is reported in Figure 21. The Delay Time tDELAY before turning off the
bridge when an overcurrent has been detected depends only by CEN value. Its magnitude is reported in Figure 22.
CEN is also used for providing immunity to pin EN against fast transient noises. Therefore the value of CEN
should be chosen as big as possible according to the maximum tolerable Delay Time and the REN value should
be chosen according to the desired Disable Time.
The resistor REN should be chosen in the range from 2.2K to 180K. Recommended values for REN and CEN
are respectively 100K
and 5.6nF that allow obtaining 200s Disable Time.
Figure 20. Overcurrent Protection Waveforms
ISOVER
IOUT
Vth(ON)
Vth(OFF)
VEN(LOW)
VDD
tOCD(ON)
tD(ON)EN
tEN(FALL)
tEN(RISE)
tDISABLE
tDELAY
tOCD(OFF)
tD(OFF)EN
VEN
BRIDGE
ON
OFF
OCD
ON
OFF
D02IN1400
相关PDF资料 |
PDF描述 |
|---|---|
| L6208PD | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO36 |
| L6219DS | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| L6219DS013TR | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| L6227Q | BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6228D | STEPPER MOTOR CONTROLLER, 2.8 A, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6208D | 制造商:STMicroelectronics 功能描述:Supply Voltage Max.:52V |
| L6208D013TR | 功能描述:马达/运动/点火控制器和驱动器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6208D013TR-CUT TAPE | 制造商:ST 功能描述:L6208 Series Dual 52 V 5.6 A DMOS Driver for Bipolar Stepper Motor - SOIC-24 |
| L6208N | 功能描述:马达/运动/点火控制器和驱动器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6208PD | 功能描述:马达/运动/点火控制器和驱动器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。