- 您现在的位置：买卖IC网 > PDF目录30712 > L6219DS-T STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF资料下载
参数资料
| 型号： | L6219DS-T |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封装： | LEAD FREE, MS-013AD, SOIC-24 |
| 文件页数： | 6/9页 |
| 文件大小： | 466K |
| 代理商： | L6219DS-T |
Dual Full-Bridge PWM Motor Driver
L6219DS
5
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Applications Information
PWM Current Control
The L6219DS dual bridge is designed to drive both windings of
a bipolar stepper motor. Output current is sensed and controlled
independently in each bridge by an external sense resistor (RS),
internal comparator, and monostable multivibrator.
When the bridge is turned on, current increases in the motor
winding and it is sensed by the external sense resistor until
the sense voltage (VCOMPIN) reaches the level set at the
comparator’s input:
ITRIP = VREF/10 RS
The comparator then triggers the monostable which turns off
the source driver of the bridge. The actual load current peak
will be slightly higher than the trip point (especially for low-
inductance loads) because of the internal logic and switching
delays. This delay (td) is typically 2 μs. After turn-off, the
motor current decays, circulating through the ground-clamp
diode and sink transistor. The source driver’s off time (and
therefore the magnitude of the current decrease) is determined
by the monostable’s external RC timing components, where
toff = RTCT within the range of 20 kΩ to 100 kΩ and 100 pF to
1000 pF.
The xed-off time should be short enough to keep the current
chopping above the audible range (< 46 μs) and long enough to
properly regulate the current. Because only slow-decay current
control is available, short off times (< 10 μs) require additional
efforts to ensure proper current regulation. Factors that can
negatively affect the ability to properly regulate the current
when using short off times include: higher motor-supply
voltage, light load, and longer than necessary blank time.
When the source driver is re-enabled, the winding current (the
sense voltage) is again allowed to rise to the comparator’s
threshold. This cycle repeats itself, maintaining the average
motor winding current at the desired level.
Loads with high distributed capacitances may result in high
turn-on current peaks. This peak (appearing across RS) will
attempt to trip the comparator, resulting in erroneous current
control or high-frequency oscillations. An external RCCC
time delay should be used to further delay the action of the
comparator. Depending on load type, many applications will
not require these external components (SENSE connected to
COMP IN).
+
–
0
Dwg. W M-003-1A
V PHAS E
I
OUT
td
toff
I TR IP
Dwg. E P -006-1
R S
BB
V
BR IDG E ON
SOUR C E OF F
ALL OF F
PWM Output Current Wave Form
Load Current Paths
相关PDF资料 |
PDF描述 |
|---|---|
| L6382D5TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| L6382D5 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| L64005-F | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| L64007 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| L64013A1 | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6219DSTR | 功能描述:IC MOTOR DRVR PWM DUAL 24SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| L6219DSTR-T | 功能描述:IC MOTOR DRIVER PWM DUAL 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| L6219L-S24-R | 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:DUAL FULL-BRIDGE PWM MOTOR DRIVER |
| L6219L-S24-T | 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:DUAL FULL-BRIDGE PWM MOTOR DRIVER |
| L6219R | 功能描述:马达/运动/点火控制器和驱动器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。