- 您现在的位置：买卖IC网 > PDF目录69003 > L6219DS013TR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF资料下载
参数资料
| 型号： | L6219DS013TR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封装： | SO-24 |
| 文件页数： | 7/11页 |
| 文件大小： | 172K |
| 代理商： | L6219DS013TR |
5/11
L6219
3
Functional Description
The circuit is intended to drive both windings of a bipolar stepper motor.
The peak current control is generated through switch mode regulation.There is a choice of three different current
levels with the two logic inputs I01 - I11 for winding 1 and I02 - I12 for winding 2.
The current can also be switched off completely.
3.1 Input Logic (I0 and I1)
The current level in the motor winding is selected with these inputs. (See fig. 5). If any of the logic inputs is left
open, the circuit will treat it has a high level input.
3.2 Phase
This input determines the direction of current flow in the windings, depending on the motor connections. The
signal is fed through a Schmidt-trigger for noise immunity, and through a time delay in order to guarantee that
no short-circuit occurs in the output stage during phase-shift.High level on the PHASE input causes the motor
current flow from Out A through the winding to Out B
3.3 Current Sensor
This part contains a current sensing resistor (RS), a low pass filter (RC, CC) and three comparators.Only one
comparator is active at a time. It is activated by the input logic according to the current level chosen with signals
Io and I1.The motor current flows through the sensing resistor RS.When the current has increased so that the
voltage across RS becomes higher than the reference voltage on the other comparator input, the comparator
goes high, which triggers the pulse generator.
The max peak current Imax can be defined by:
3.4 Single-pulse Generator
The pulse generator is a monostable triggered on the positive going edge of the comparator output.The
monostable output is high during the pulse time, toff , which is determined by the time components Rt and Ct.
toff = 1.1 RtCt
The single pulse switches off the power feed to the motor winding, causing the winding current to decrease dur-
ing toff. If a new trigger signal should occur during toff, it is ignored.
3.5 Output Stage
The output stage contains four Darlington transistors (source drivers) four saturated transistors (sink drivers)
and eight diodes, connected in two H bridge.
Table 6.
I0
I1
Current Level
H
No Current
L
H
Low current 1/3 IO max
H
L
Medium current 2/3 IO max
L
Maximum current IO max
I
max
V
ref
10R
s
--------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| L6227Q | BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6228D | STEPPER MOTOR CONTROLLER, 2.8 A, PDSO24 |
| L6228N | STEPPER MOTOR CONTROLLER, 2.8 A, PDIP24 |
| L6229QTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6229Q | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, QCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6219DS013TRE | 制造商:STMicroelectronics 功能描述: |
| L6219DSA | 功能描述:马达/运动/点火控制器和驱动器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6219DSA_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Stepper motor driver for automotive range |
| L6219DSA13TR | 功能描述:马达/运动/点火控制器和驱动器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6219DS-T | 功能描述:IC MOTOR DRVR PWM DUAL 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
发布紧急采购，3分钟左右您将得到回复。