- 您现在的位置：买卖IC网 > PDF目录43899 > L6223 (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 6 A, PDIP20 PDF资料下载
参数资料
| 型号： | L6223 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 6 A, PDIP20 |
| 封装： | POWER, DIP-20 |
| 文件页数： | 25/33页 |
| 文件大小： | 3431K |
| 代理商： | L6223 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页
Figure 36: Peak transient Rth pulse width and Duty Cycle.
Notes on the p.c.b. design.
We recommend to observe the following layout
rules to avoid application problems associated
with ground loops and anomalous recirculation
currents. The by-pass capacitors for the power
and logic supply must to be kept as close to the
IC as possible.
It’s important to separate on the PCB board the
logic and the power grounds avoiding that
grounds traces of the logic signals cross the
ground traces of the power signals. The starpoint
grounding, the point of the board in which the
logic ground meets the power ground, should be
kept far enough away from where the power
ground traces terminate to ground (sense resis-
tors and protection zener diodes traces). This
avoids interference with the logic signals. Be-
cause the IC uses the board as a heatsink the
dissipating copper area must be sized in accord-
ance with the required value of Rthj-amb. It’s impor-
tant to provide a good filter for the logic supply,
especially for the resistor of the oscillator net-
work. In addition, the capacitor ground of the RC
network must be as clean as possible. When the
ground is used also to heatsink, it is helpful to
use either a polistyrin capacitor or one with a low
temperature coefficient. The value of the boot-
strap capacitor is not a critical parameter, never-
theless the use of a capacitor of 10nF
±20% is
recommended. A non-inductive resistor is the
best way to implement the sensing, but when that
is not possible, more metalfilm resistors of the
same value can be paralleled.
L6223
31/33
相关PDF资料 |
PDF描述 |
|---|---|
| L6225PDTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
| L6225PD | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
| L6225D | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
| L6226DTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO24 |
| L6226D | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6223A | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| L6225 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DMOS DUAL FULL BRIDGE DRIVER |
| L6225_03 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DMOS DUAL FULL BRIDGE DRIVER |
| L6225D | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6225DTR | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。