- 您现在的位置：买卖IC网 > PDF目录43899 > L6226Q (STMICROELECTRONICS) BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 PDF资料下载
参数资料
| 型号： | L6226Q |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| 封装： | 5 X 5 MM, 1 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32 |
| 文件页数： | 4/29页 |
| 文件大小： | 480K |
| 代理商： | L6226Q |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Circuit description
L6226Q
12/29
Doc ID 14335 Rev 5
4.3
Truth table
4.4
Non-dissipative overcurrent detection and protection
An overcurrent detection circuit (OCD) is integrated. This circuit can be used to provides
protection against a short circuit to ground or between two phases of the bridge as well as a
roughly regulation of the load current. With this internal over current detection, the external
current sense resistor normally used and its associated power dissipation are eliminated.
Figure 9 shows a simplified schematic of the overcurrent detection circuit for the bridge A.
bridge B is provided of an analogous circuit.
To implement the over current detection, a sensing element that delivers a small but precise
fraction of the output current is implemented with each high side power MOS. Since this
current is a small fraction of the output current there is very little additional power
dissipation. This current is compared with an internal reference current IREF. When the
output current reaches the detection threshold Isover the OCD comparator signals a fault
condition. When a fault condition is detected, an internal open drain MOS with a pull down
capability of 4 mA connected to OCD pin is turned on. Figure 10 shows the OCD operation.
This signal can be used to regulate the output current simply by connecting the OCD pin to
EN pin and adding an external R-C as shown in Figure 9. The off time before recovering
normal operation can be easily programmed by means of the accurate thresholds of the
logic inputs.
IREF and, therefore, the output current detection threshold are selectable by RCL value,
following the equations:
●
Isover = 2.8 A ± 30 % at -25 °C < TJ < 125 °C if RCL = 0 Ω
(PROGCL connected to GND)
●
Isover =
±10 % at -25 °C < TJ < 125 °C if 5 kΩ < RCL < 40 kΩ
to 40 k
Ω.
The disable time tDISABLE before recovering normal operation can be easily programmed by
means of the accurate thresholds of the logic inputs. It is affected whether by CEN and REN
Table 7.
Truth table
Inputs
Outputs
EN
IN1
IN2
OUT1
OUT2
LX (1)
1.
X = Don't care
X
High Z (2)
2.
High Z = High impedance output
High Z
HL
L
GND
HH
L
Vs
GND
HLH
GND
Vs
HH
H
Vs
11050
R
CL
----------------
相关PDF资料 |
PDF描述 |
|---|---|
| L6227N | STEPPER MOTOR CONTROLLER, 2.8 A, PDIP24 |
| L6228Q | STEPPER MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6228QTR | STEPPER MOTOR CONTROLLER, QCC32 |
| L6229D | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO24 |
| L6229N | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDIP24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6226Q_10 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DMOS dual full bridge driver |
| L6226QTR | 功能描述:功率驱动器IC DMOS Full Bridge Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| L6227 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DMOS DUAL FULL BRIDGE DRIVER WITH PWM CURRENT CONTROLLER |
| L6227D | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6227DTR | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。