- 您现在的位置：买卖IC网 > PDF目录39185 > L6235D (STMICROELECTRONICS) BRUSHLESS DC MOTOR CONTROLLER, 5.6 A, PDSO24 PDF资料下载
参数资料
| 型号： | L6235D |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 5.6 A, PDSO24 |
| 封装： | SO-24 |
| 文件页数： | 10/25页 |
| 文件大小： | 442K |
| 代理商： | L6235D |
L6235
18/25
APPLICATION INFORMATION
A typical application using L6235 is shown in Figure 21. Typical component values for the application are shown
in Table 3. A high quality ceramic capacitor (C2) in the range of 100nF to 200nF should be placed between the
power pins VSA and VSB and ground near the L6235 to improve the high frequency filtering on the power supply
and reduce high frequency transients generated by the switching. The capacitor (CEN) connected from the EN
input to ground sets the shut down time when an over current is detected (see Overcurrent Protection). The two
current sensing inputs (SENSEA and SENSEB) should be connected to the sensing resistor RSENSE with a trace
length as short as possible in the layout. The sense resistor should be non-inductive resistor to minimize the di/
dt transients across the resistor. To increase noise immunity, unused logic pins are best connected to 5V (High
Logic Level) or GND (Low Logic Level) (see pin description). It is recommended to keep Power Ground and
Signal Ground separated on PCB.
Table 3. Component Values for Typical Application.
Figure 21. Typical Application
C1
100F
R1
5K6
C2
100nF
R2
1K8
C3
220nF
R3
4K7
CBOOT
220nF
R4
1M
COFF
1nF
RDD
1K
CPUL
10nF
REN
100K
CREF1
33nF
RP
100
CREF2
100nF
RSENSE
0.3
CEN
5.6nF
ROFF
33K
CP
10nF
RPUL
47K
D1
1N4148
RH1, RH2, RH3
10K
D2
1N4148
VREF
+
-
BRAKE
14
5
18
19
21
16
OUT1
H1
H2
H3
GND
RCOFF
OUT3
OUT2
VSA
POWER
GROUND
SIGNAL
GROUND
+5V
+
-
VS
8-52VDC
13
VSB
VCP
VBOOT
CP
CBOOT
RP
D2
D1
C1
C2
SENSEA
RSENSE
20
BRAKE
6
7
DIAG
EN
CEN
REN
ENABLE
2
FWD/REV
11
TACHO
8
12
1
23
24
4
17
3
15
22
SENSEB
THREE-PHASE MOTOR
COFF
ROFF
RH1
RH2
RH3
10
CREF1
R2
R3
R1
RDD
R4
C3
CREF2
RCPULSE
9
CPUL
RPUL
D02IN1357
M
VREF
5V
HALL
SENSOR
相关PDF资料 |
PDF描述 |
|---|---|
| L6239 | DISK DRIVE MOTOR CONTROLLER, 2.2 A, PQCC44 |
| L6258 | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO36 |
| L6271 | DISK DRIVE MOTOR CONTROLLER, PDSO24 |
| L6726A | 1.5 A SWITCHING CONTROLLER, 297 kHz SWITCHING FREQ-MAX, PDSO8 |
| L6997STR | SWITCHING CONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6235D013TR | 功能描述:马达/运动/点火控制器和驱动器 Three Phase Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6235N | 功能描述:马达/运动/点火控制器和驱动器 Three Phase Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6235PD | 功能描述:马达/运动/点火控制器和驱动器 Three Phase Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6235PD013TR | 功能描述:马达/运动/点火控制器和驱动器 Three Phase Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6235Q | 功能描述:马达/运动/点火控制器和驱动器 DMOS 3-Phase DC 5.6A 0.3 Ohm 100kHz RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。