- 您现在的位置：买卖IC网 > PDF目录67754 > L6728 (STMICROELECTRONICS) 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10 PDF资料下载
参数资料
| 型号： | L6728 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10 |
| 封装： | 3 X 3 MM, LEAD FREE, DFN-10 |
| 文件页数： | 27/31页 |
| 文件大小： | 1361K |
| 代理商： | L6728 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页
Obsolete
Product(s)
- Obsolete
Product(s)
L6728
Pin description and connection diagrams
2
Pin description and connection diagrams
2.1
Pin descriptions
Figure 3.
Pin connection (top view)
Table 2.
Pins description
Pin #
Name
Function
1BOOT
HS driver supply.
Connect through a capacitor (100 nF) to the floating node (LS-Drain) pin
and provide necessary bootstrap diode from VCC.
2
PHASE
HS driver return path, current-reading and adaptive-dead-time monitor.
Connect to the LS drain to sense
RDS(on) drop to measure the output
current. This pin is also used by the adaptive-dead-time control circuitry to
monitor when HS MOSFET is OFF.
3
UGATE
HS driver output. Connect directly to HS MOSFET gate.
4
LGATE / OC
LGATE. LS driver output. Connect directly to LS MOSFET gate.
OC. Over Current threshold set. During a short period of time following
VCC rising over UVLO threshold, a 10
μA current is sourced from this pin.
Connect to GND with an ROCSET resistor greater than 5 kΩ to program OC
Threshold. The resulting voltage at this pin is sampled and held internally
as the OC set point. Maximum programmable OC threshold is 0.55 V. A
voltage greater than 0.6 V activates an internal clamp and causes OC
threshold to be set at the maximum value.
5GND
All internal references, logic and drivers are connected to this pin.
Connect to the PCB ground plane.
6VCC
Device and drivers power supply.
Operative range from 5 V to 12 V. Filter with at least 1 nF MLCC to GND.
7
COMP / DIS
COMP. Error amplifier output. Connect with an RF - CF // CP to FB to
compensate the device control loop.
DIS. The device can be disabled by pushing this pin lower than 0.75 V (typ).
Setting free the pin, the device enables again.
8FB
Error amplifier inverting input.
Connect with a resistor RFB to the output regulated voltage. Output resistor
divider may be used to regulate voltages higher than the reference.
相关PDF资料 |
PDF描述 |
|---|---|
| L6728TR | 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10 |
| L6731BTR | 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6731B | 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6731D | 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16 |
| L9230-DIE1 | STEPPER MOTOR CONTROLLER, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6728_0706 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Single phase PWM controller with Power Good |
| L6728A | 功能描述:电压模式 PWM 控制器 Hi-Freq. singl-phase PWM controller w/Po RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| L6728AH | 功能描述:软开关 PWM 控制器 Sgl Output 600 KHz DFPN-10 RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| L6728AHTR | 功能描述:电流型 PWM 控制器 HIGH FREQ PWM CNTRL W/PO RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L6728ATR | 功能描述:电压模式 PWM 控制器 HIGH FREQ SINGLE PHASE PWM CNTRL RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。