参数资料
型号: L6731B
厂商: STMICROELECTRONICS
元件分类: 稳压器
英文描述: 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
封装: HTSSOP-16
文件页数: 7/24页
文件大小: 439K
代理商: L6731B
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
L6731B
Device description
15/24
The device realizes the over-current-protection (OCP) sensing the current both on the high-
side MOSFET(s) and the low-side MOSFET(s) and so 2 current limit thresholds can be set (see
OCH pin and OCL pin in Table 3. Pins function):
Peak Current Limit
Valley Current Limit
The Peak Current Protection is active when the high-side MOSFET(s) is turned on, after a
masking time of about 100ns. The valley-current-protection is enabled when the low-side
MOSFET(s) is turned on after a masking time of about 400ns. If, when the soft-start phase is
completed, an over current event occurs during the on time (peak-current-protection) or during
the off time (valley-current-protection) the device enters in HICCUP mode: the high-side and
low-side MOSFET(s) are turned off, the soft-start capacitor is discharged with a constant
current of 10A and when the voltage at the SS pin reaches 0.5V the soft-start phase restarts.
During the soft-start phase the OCP provides a constant-current-protection. If during the TON
the OCH comparator triggers an over current the high-side MOSFET(s) is immediately turned
off (after the masking time and the internal delay) and returned on at the next pwm cycle. The
limit of this protection is that the TON can't be less than masking time plus propagation delay
because during the masking time the peak-current-protection is disabled. In case of very hard
short circuit, even with this short TON, the current could escalate. The valley-current-protection
is very helpful in this case to limit the current. If during the off-time the OCL comparator triggers
an over current, the high-side MOSFET(s) is not turned on until the current is over the valley-
current-limit. This implies that, if it is necessary, some pulses of the high-side MOSFET(s) will
be skipped, guaranteeing a maximum current due to the following formula:
In constant current protection a current control loop limits the value of the error amplifier output
(comp), in order to avoid its saturation and thus recover faster when the output returns in
regulation. Figure 9. shows the behaviour of the device during an over current condition that
persists also in the soft-start phase.
Figure 8.
OVP: the low-side MOSFET is turned-on in advance.
VOUT
VFB
LGate
109%
MIN
ON
VALLEY
MAX
T
L
Vout
Vin
I
,
+
=
相关PDF资料
PDF描述
L6731D 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
L9230-DIE1 STEPPER MOTOR CONTROLLER, UUC
L9230 STEPPER MOTOR CONTROLLER, PDSO20
LA5680T SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQFP48
LA5681T SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, PQFP48
相关代理商/技术参数
参数描述
L6731BTR 功能描述:IC CTRLR ADJ STEP DOWN 16-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源,ICERA E400,E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA,WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR)
L6731D 功能描述:DC/DC 开关控制器 Adjustable Step Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
L6731DTR 功能描述:DC/DC 开关控制器 Adjustable Step Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
L6732 功能描述:DC/DC 开关控制器 Adjustable Step Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
L6732_08 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Adjustable step-down controller with synchronous rectification