- 您现在的位置：买卖IC网 > PDF目录67127 > L9907ND (STMICROELECTRONICS) BRUSH DC MOTOR CONTROLLER, 0.8 A, PDSO20 PDF资料下载
参数资料
| 型号： | L9907ND |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 0.8 A, PDSO20 |
| 封装： | SO-20 |
| 文件页数： | 5/8页 |
| 文件大小： | 159K |
| 代理商： | L9907ND |
An external resistor RCF is recommended be-
tween the slider of the control and feedback po-
tentiometer.
This resistor assures that in the case of input con-
trol or input feedback wire interruption the input
differential voltage will be within the NEUTRAL
ZONE and the motor position remains frozen.
The circuit features an overvoltage disable func-
tion referred to the supply voltage VS higher than
18V, both outputs are forced to tristate in this con-
dition.
The thermal overload function disables the out-
puts (tristate) when the junction temperature in-
creases above the thermal shutdown threshold
temperature of min. 150°C.
For the start of a heavy loaded motor, if the motor
current reaches the max. value it is necessary to
respect the dynamical thermal resistance junction
to ambient. The maximum output current is 0.8A.
The maximum junction temperature in this phase
should not increase above the thermal shutdown
threshold. In case of output disable due to ther-
mal overload the output remains disabled till the
junction temperature decreases under the thermal
enable threshold. This behaviour is assured with
the thermal shutdown hysteresis threshold , which
minimum value is 20°C.
Figure 3, 5 and 7 show typical application dia-
grams for headlight adjustment applications. To
assure the safety of the circuits in the reverse bat-
tery condition a reverse protection diode D1, is
necessary.
The input currents in this condition are limited by
the resistors RINC and RINF. The transient protec-
tion diode D2 must assure that the maximum rat-
ing for VS during the transients at VBAT line will be
limited to a value lower than absolute maximum
VBAT
VS -2V
1.5V
VF
0
1.5V
VS -2V
VBAT
VC
D95AT185A
Figure 4: Control to feedback transfer characteristic
for proportional regulation with extended
VC operating range:
D1
D2
CS
IQ
RC
VINC
RINF
RINC1
RPR
RINC2
PR
L9907N
IINC
INC
VINF
IINF
INF
VS
RF
VC
VF
GND
OUT C
OUT F
M
VM
IM
VBAT
D95AT186
MODULE
Figure 5: Recommended Application Circuit Diagram with L9907N for proportional regulation with extended
VC operating range. For ideal adjusted condition VF
=
RINC2
RINC1
+ RINC2
VC:
Note:
Recommended value of RINC, RINF (equivalent input resistance to INC and INF) is 5K
to 10K. If the motor should not change its position, when
the control signal wire become open, RINC1 and RINC2 should be rated so that VINC
≤ 0.4V in this condition.
L9907N
5/8
相关PDF资料 |
PDF描述 |
|---|---|
| LB1855M | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO16 |
| LB1945D | STEPPER MOTOR CONTROLLER, 1 A, PDFM28 |
| LB1945D | STEPPER MOTOR CONTROLLER, 1 A, PDFM28 |
| LB1948M | STEPPER MOTOR CONTROLLER, PDSO10 |
| LSS-T/10-W12 | 1-OUTPUT 60 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L9907ND013TR | 功能描述:马达/运动/点火控制器和驱动器 Motor Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9907TR | 功能描述:IC FET DVR 3PHASE BLDC 64TQFP 制造商:stmicroelectronics 系列:汽车级，AEC-Q100 包装:剪切带（CT） 零件状态:在售 驱动配置:半桥 通道类型:3 相 驱动器数:6 栅极类型:N 沟道 MOSFET 电压 - 电源:5 V ~ 54 V 逻辑电压?- VIL，VIH:0.8V，2V 电流 - 峰值输出（灌入，拉出）:- 输入类型:- 上升/下降时间（典型值）:35ns，35ns 工作温度:-40°C ~ 150°C（TJ） 安装类型:表面贴装 封装/外壳:64-TQFP 裸露焊盘 供应商器件封装:64-TQFP（10x10） 标准包装:1 |
| L9909 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DC MOTOR DRIVER WITH POSITION CONTROL |
| L9911 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:CAR ALTERNATOR MULTIFUNCTION SMART VOLTAGE REGULATOR |
| L9911A | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:CAR ALTERNATOR MULTIFUNCTION SMART VOLTAGE REGULATOR |
发布紧急采购，3分钟左右您将得到回复。