- 您现在的位置：买卖IC网 > PDF目录32287 > L9953LXP (STMICROELECTRONICS) SPECIALTY CONSUMER CIRCUIT, PDSO36 PDF资料下载
参数资料
| 型号： | L9953LXP |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO36 |
| 封装： | ROHS COMPLAINT, SSOP-36 |
| 文件页数： | 16/35页 |
| 文件大小： | 505K |
| 代理商： | L9953LXP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
L9953LXP
Application information
Doc ID 16185 Rev 1
3.13
Programmable soft start function to drive loads with higher
inrush current
Loads with start-up currents higher than the over-current limits (e.g. inrush current of lamps,
start current of motors and cold resistance of heaters) can be driven by using the
programmable soft start function (i.e. overcurrent recovery mode). Each driver has a
corresponding over-current recovery bit. If this bit is set, the device will automatically switch-
on the outputs again after a programmable recovery time. The duty cycle in over-current
condition can be programmed by the SPI interface to be about 12% or 25%. The PWM
modulated current will provide sufficient average current to power up the load (e.g. heat up
the bulb) until the load reaches operating condition. The PWM frequency settles at 3kHz or
6kHz. The device itself cannot distinguish between a real overload and a non linear load like
a light bulb. A real overload condition can only be qualified by time. As an example the
microcontroller can switch on light bulbs by setting the over-current recovery bit for the first
50ms. After clearing the recovery bit the output will be automatically disabled if the overload
condition still exits.
Figure 9.
Programmable soft start function for inductive loads and incandescent
bulbs
Load Current
Overcurrent
detection
Unlimited Inrush Current
Limited Inrush Current in
overcurrent recovery mode
with inductive load
t
Load Current
Overcurrent
detection
Unlimited Inrush Current
Limited Inrush Current in
overcurrent recovery mode with
incandescent bulb
t
相关PDF资料 |
PDF描述 |
|---|---|
| LA1177 | 1-BAND, AUDIO TUNER, PSIP9 |
| LA1178M | 1-BAND, AUDIO TUNER, PDSO10 |
| LA1186N | 1-BAND, AUDIO TUNER, PSIP9 |
| LA1787M | AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP64 |
| LA1787M | AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L9953LXPTR | 功能描述:马达/运动/点火控制器和驱动器 DOOR ACTUATOR DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9953TR | 功能描述:马达/运动/点火控制器和驱动器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9953XP | 功能描述:马达/运动/点火控制器和驱动器 Door actuator DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9953XPTR | 功能描述:马达/运动/点火控制器和驱动器 Door actuator DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9954 | 功能描述:马达/运动/点火控制器和驱动器 Door actuator DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。